Keysight Technologies N5221BU-605 Installation Note Download Page 7

Page: 7 / 88

Installation Note N5222-90114 7

Getting Prepared

If the model number, serial number, or option number do not match those on

the license message you received from Keysight, you will not be able to install

the license key file. If this is the case, contact Keysight for assistance. Refer to

“Getting Assistance from Keysight” on page 4

Verify the Model/Version of HMA26.5 Installed

This upgrade kit contains components for use with PNA models using the

legacy HMA26.5 part number 5087-7765. If your PNA has the newer HMA26.5

part number N5240-60101 installed you may discard these parts:

— A22 splitter 5087-7139
— W42 N5222-20009
— W43 N5222-20007
— W44 N5222-20008

(If you have the legacy 5086-7765 HMA26.5, please discard the N5245-20195

semi-rigid cables. Refer to

Figure 1 on page 7

The new N5240-60101 HMA26.5 has the splitter integrated into the assembly.

Refer to

Figure 1 on page 7

Figure 1

Comparison of Legacy HMA26.5 (5087-7765) and New HMA26.5

(N5240-60101)

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands