Keysight Technologies E4981A Service Manual Download Page 116

Page: 116 / 152

114

Chapter 6

Replacement Procedure

GPIB Assembly Replacement

Tools Required

•

Torque screwdriver, TORX T10

•

Torque screwdriver, TORX T20

•

Box torque wrench, 7 mm

Removal Procedure

Refer to

Figure 6-16

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Interface Board Assembly as described in

“Interface Board Assembly

Replacement” on page 105

Step 4.

Disconnect the GPIB cable (item 1) from the Rear Panel.

Step 5.

Remove the two 7mm standoff (item 2) fastening the GPIB Assembly.

Step 6.

Remove the GPIB Assembly (item 3).

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Figure 6-16

GPIB Assembly Replacement

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands