manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

227

Keysight InfiniiVision 2000 X-Series Oscilloscopes 

User's Guide

 

15 Mask Testing

To create a mask from a "golden" waveform (Automask) / 227
Mask Test Setup Options / 229
Mask Statistics / 232
To manually modify a mask file / 233
Building a Mask File / 236

One way to verify a waveform's compliance to a particular set of parameters is to 

use mask testing. A mask defines a region of the oscilloscope's display in which 

the waveform must remain in order to comply with chosen parameters. 

Compliance to the mask is verified point-by-point across the display. Mask test 

operates on displayed analog channels; it does not operate on channels that are 

not displayed.

Mask test is a license-enabled feature.

To create a mask from a "golden" waveform (Automask)

A golden waveform meets all chosen parameters, and it is the waveform to which 

all others will be compared.

1

Configure the oscilloscope to display the golden waveform.

2

Press the 

[Analyze]

 key.

3

Press 

Features

; then, select 

Mask Test

.

4

Press 

Features

 again to enable mask testing.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Canta V5 Quick Manual preview
V5
Brand: Canta Pages: 2
BACtrack S75 Owner'S Manual preview
S75
Brand: BACtrack Pages: 13
TA Instruments DHR Series Getting Started Manual preview
DHR Series
Brand: TA Instruments Pages: 35
Bang & Olufsen BeoPlay A9 Quick Manual preview
BeoPlay A9
Brand: Bang & Olufsen Pages: 2
Nektar Aura Setup And User Manual preview
Aura
Brand: Nektar Pages: 3
Youkey Q7 Instructions For Use Manual preview
Q7
Brand: Youkey Pages: 86
Wacker Neuson AR Operator'S Manual preview
AR
Brand: Wacker Neuson Pages: 62
Daktronics Sportsound SSR-200 Quick Start Manual preview
Sportsound SSR-200
Brand: Daktronics Pages: 5
DB Industries DELTA 2 User Instructions preview
DELTA 2
Brand: DB Industries Pages: 60
vc999 K5 Operating Manual preview
K5
Brand: vc999 Pages: 55
Salsbury Industries 3700 Series Manual preview
3700 Series
Brand: Salsbury Industries Pages: 4
ParaBody 858 Assembly Instruction Sheet preview
858
Brand: ParaBody Pages: 5
Haaga 677 Original Operating Instructions preview
677
Brand: Haaga Pages: 31
Qlight S80S Manual preview
S80S
Brand: Qlight Pages: 3
qtran Q-VAULT-5 Installation preview
Q-VAULT-5
Brand: qtran Pages: 2
Q-Optics Radiant Instructions & Care preview
Radiant
Brand: Q-Optics Pages: 2
TEC DG-1000 Quick Manual preview
DG-1000
Brand: TEC Pages: 6
U Technology Magic Series Installation Manual preview
Magic Series
Brand: U Technology Pages: 6

Brands by name

Popular brands

Load more brands