manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

232

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

15

Mask Testing

 

Mask Statistics

From the Mask Test Menu, press the 

Statistics

 softkey to enter the Mask Statistics 

Menu.

Show Stats

When you enable 

Show Statistics

 the following information is displayed:

•

Current mask, name of mask, Channel number, date and time.

•

# of Tests (total number of mask tests executed).

•

Status (Passing, Failing, or Untested).

•

Accumulated test time (in hours, minutes, seconds, and tenths of seconds).

And for each analog channel:

•

Number of failures (acquisitions in which the signal excursion went beyond 

the mask).

•

Failure rate (percentage of failures).

•

Sigma (the ratio of process sigma to maximum achievable sigma, based on 

number of waveforms tested).

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

ZOLL X Series Operator'S Manual preview
X Series
Brand: ZOLL Pages: 344
ABB C571-AC Instructions Manual preview
C571-AC
Brand: ABB Pages: 9
Makerfire N10 Instructions Manual preview
N10
Brand: Makerfire Pages: 10
Omnia 11 Quick Start Installation Manual preview
11
Brand: Omnia Pages: 8
GE Ettan IPGphor 3 Instrument User Manual preview
Ettan IPGphor 3
Brand: GE Pages: 64
GE AMX 4+ Technical Publications preview
AMX 4+
Brand: GE Pages: 56
GE AMX 4+ Technical Manual preview
AMX 4+
Brand: GE Pages: 132
GE AKTAprocess Site Preparation Manual preview
AKTAprocess
Brand: GE Pages: 16
GE Logiq 500 Advanced Reference Manual preview
Logiq 500
Brand: GE Pages: 474
Zenbooth Duo Build Instructions preview
Duo
Brand: Zenbooth Pages: 60
ZIGBEE 624 Quick Start Manual preview
624
Brand: ZIGBEE Pages: 4
CAIRE Companion 5 Provider Technical Manual preview
Companion 5
Brand: CAIRE Pages: 38
Caframo BDC2002 Instruction Manual preview
BDC2002
Brand: Caframo Pages: 72
Hach TenSette plus User Manual preview
TenSette plus
Brand: Hach Pages: 66
Hach sensION+ pH3 User Manual preview
sensION+ pH3
Brand: Hach Pages: 14
Hach sensION MM340 User Manual preview
sensION MM340
Brand: Hach Pages: 144
Hach QuikChem 8500 2 Series Installation Manual preview
QuikChem 8500 2 Series
Brand: Hach Pages: 80
Hach SD900 Basic User Manual preview
SD900
Brand: Hach Pages: 178

Brands by name

Popular brands

Load more brands