Keysight Technologies DSO-X 2014A User Manual Download Page 206

Page: 206 / 378

206

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Measurements

Measurements Summary

The automatic measurements provided by the oscilloscope are listed in the

following table. All measurements are available for analog channel waveforms. All

measurements except Counter are available for math waveforms other than FFT. A

limited set of measurements is available for math FFT waveforms and for digital

channel waveforms (as described in the following table).

Measurement

Valid

for

Math

FFT

Valid for

Digital

Channels

Notes

Yes, Full

Screen

Yes

Measures between two sources.

Press

Settings

to specify the second

source.

Yes

Yes

Yes

Yes

"Falling Edges Count"

page 223

"Positive Pulse Count"

page 222

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands

Keysight Technologies DSO-X 2014A, User Manual

Search results

Summary of Contents for DSO-X 2014A

Reviews:

Related manuals for DSO-X 2014A

Brands by name

Popular brands