manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

Measurements

14

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

223

 

This measurement is available for analog channels.

Rising Edge Count

The 

Rising Edge Count

 measurement is an edge count for the selected waveform 

source.

This measurement is available for analog channels.

Falling Edges Count

The 

Falling Edges Count

 measurement is an edge count for the selected waveform 

source.

This measurement is available for analog channels.

Measurement Thresholds

Setting measurement thresholds defines the vertical levels where measurements 

will be taken on an analog channel or math waveform.

1

From the Measurement Menu, press the 

Settings

 softkey; then, press the 

Thresholds

 softkey to set analog channel measurement thresholds.

Negative pulse count

NOTE

Changing default thresholds may change measurement results

The default lower, middle, and upper threshold values are 10%, 50%, and 90% of the value 

between Top and Base. Changing these threshold definitions from the default values may 

change the returned measurement results for Average, Delay, Duty Cycle, Fall Time, 

Frequency, Overshoot, Period, Phase, Preshoot, Rise Time, +Width, and -Width.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Panasonic AJSPD850P - P2 DECK Operating Instructions Manual preview
AJSPD850P - P2 DECK
Brand: Panasonic Pages: 73
Backyard Discovery BELMONT 2001039 Manual preview
BELMONT 2001039
Brand: Backyard Discovery Pages: 50
Backyard Discovery 6613 Owner'S Manual & Assembly Instructions preview
6613
Brand: Backyard Discovery Pages: 45
Backyard Discovery BEACH FRONT Owner'S Manual preview
BEACH FRONT
Brand: Backyard Discovery Pages: 70
BACtrack ELEMENT Product Manual preview
ELEMENT
Brand: BACtrack Pages: 16
Eastern Jungle Gym CLASSIC Owner'S Instruction Manual preview
CLASSIC
Brand: Eastern Jungle Gym Pages: 17
Vahle VCL Series Translation Of The Original Operating Instructions preview
VCL Series
Brand: Vahle Pages: 96
IDS Dual Product Manual preview
Dual
Brand: IDS Pages: 2
Raytheon V300 Instruction Manual preview
V300
Brand: Raytheon Pages: 68
KegLand Cannular Instruction Manual preview
Cannular
Brand: KegLand Pages: 23
ParaBody 801 Assembly Instruction Sheet preview
801
Brand: ParaBody Pages: 3
Valiani OMNIA Instruction And Maintenance Manual preview
OMNIA
Brand: Valiani Pages: 66
NARGESA PC16 Instruction Book preview
PC16
Brand: NARGESA Pages: 37
NARGESA NOA60 Technical Features preview
NOA60
Brand: NARGESA Pages: 6
Ocean Sonics icListen User Manual preview
icListen
Brand: Ocean Sonics Pages: 45
PASCO TD-8572 Instruction Manual And Experiment Manual preview
TD-8572
Brand: PASCO Pages: 5
Pasco Scientific OS-9255A Instruction Manual preview
OS-9255A
Brand: Pasco Scientific Pages: 27
PARUS TERA Instruction Manual preview
TERA
Brand: PARUS Pages: 6

Brands by name

Popular brands

Load more brands