manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 164

 6-8                                                                                Electronic Calibration Modules Reference Guide

Replaceable Parts
3.5 mm Modules and Accessories

6-

3.5 mm Modules and Accessories

Table 6-7 3.5 mm Modules and Accessories

Description

a

a. See 

“Clarifying the Terminology of a Connector Interface” on page 1-1

.

Qty

Part Number

Adapters (added with Option 00A – N469xD only)

3.5 mm -f- to -f- adapter

 

3.5 mm -m- to -m- adapter

1

 

1

85052-60012

 

85052-60014

Protective End Caps

3.5 mm -f-f connector cap (for module) 

b

 

3.5 mm -m-m connector cap (for module) 

b

 

3.5 mm -m-f connector cap (for module) 

b

 

3.5 mm -f- connector cap (for adapter) 

c

 

3.5 mm -m- connector cap (for adapter) 

c

b. Available on the N755xA ECals only.

c. These items are not included, but can be ordered separately.

1

 

1

 

1

 

as required

 

as required

N7550-40001

 

N7550-40003

 

N7550-40002

 

1401-0202

 

1401-0208

Gages 

c

3.5 mm -f- pin-depth gage 

d

 

3.5 mm -m- pin-depth gage 

d

d. A 3.5 mm gage is capable of measuring 3.5 mm and 2.92 mm connectors.

1

 

1

11752-60105

 

11752-60106

Other

Electronic calibration module reference guide (online)

 

USB cable A to B, 2 meter

 

1/2 in to 9/16 in open-ended wrench 

c

 

20 mm, 90 N-cm (8 in-lb) torque wrench 

c

 

5/16 in, 90 N-cm (8 in-lb) torque wrench 

c

 

Spanner wrench 

c

 

Ruggedized plastic storage box for the ECal module and accessories (Option 
150) 

c

 

 

 

 

Replacement ruggedized plastic storage box for the ECal module and 
accessories

e

 

 

e. This item is included, but a replacement can be ordered separately.

1

 

1

 

1

 

1

 

1

 

1

 

1

 

1

 

 

 

 

 

1

N7550-90002

 

8121-2671

 

8710-1770

 

8710-1764

 

8710-1765

 

08513-20014
N7550-60009 – Refer 

to 

Table 1-2, 

“N755xA 

Modules”, on 

page 1-10

.

 

1540-2345 – Refer to 

Table 1-5, 

“N469xD 

Modules”, on 

page 1-17

.

 

1540-2367 – Refer to 

Table 1-1, “8509xD 

Modules”, on 

page 1-8

.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands