manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 18

 1-10                                                                                Electronic Calibration Modules Reference Guide

General Information
Models and Options

1-

Table 1-2 

N755xA Modules

Model

Number

Connector

Type

Operating

a

Frequency

Port A and B Option

-m- and -f-

-m- and -m-

-f- and -f-

N7550A

Type-N 50 ohm

DC to 4 GHz

N7550A-NMF

N7550A-NMM

N7550A-NFF

3.5 mm

N7550A-3MF

N7550A-3MM

N7550A-3FF

N7551A

Type-N 50 ohm

 

DC to 6.5 GHz

N7551A-NMF

N7551A-NMM

N7551A-NFF

3.5 mm 

N7551A-3MF

N7551A-3MM

N7551A-3FF

N7552A

Type-N 50 ohm

 

DC to 9 GHz

N7552A-NMF

N7552A-NMM

N7552A-NFF

3.5 mm

N7552A-3MF

N7552A-3MM

N7552A-3FF

 

N7553A

Type-N 50 ohm

 

DC to 14 GHz

N7553A-NMF

N7553A-NMM

N7553A-NFF

3.5 mm

N7553A-3MF

N7553A-3MM

N7553A-3FF

N7554A

Type-N 50 ohm

 

DC to 18 GHz

N7554A-NMF

N7554A-NMM

N7554A-NFF

3.5 mm

N7554A-3MF

N7554A-3MM

N7554A-3FF

N7555A

3.5 mm

DC to 26.5 GHz

N7555A-3MF

N7555A-3MM

N7555A-3FF

a. Option 0DC frequency range is DC to xx.x GHz. Option 100 frequency range is 10 MHz to xx.x GHz. 

N755xA Other 

Options

Description 

A6J

ANSI Z540-1-1994 Calibration

1A7

Calib Uncerta Guardbanding

UK6

Adds commercial calibration certificate with measured data.

SPS

Post Sales Support

150

ECal ruggedized plastic storage box – See also 

“ECal Kit Storage Box (Option 150) – 

(N755xA Only)” on page 4-23

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands