background image

Important Safety Information

Prior to assembly, remove components from the box and verify that all the listed parts were 
supplied.  

WARNING!

 Before using this unit or starting any exercise program, consult your 
physician.  This is especially important for persons over the age of 
35 and/or persons with pre-existing health problems.  Keys Fitness 
Products LP assumes no responsibility for personal injury or property 
damage sustained by or through the use of this product.

It is the owner’s responsibility to ensure that all users of this unit 
have read the Owner’s Manual and are familiar with safety informa-
tion and precautions.

SAFETY PRECAUTIONS

•  This unit should only be used on a level surface and is intended for 

indoor use only. Keys Fitness recommends an equipment mat be 
placed under the unit to protect the floor or carpet and for easier 
cleaning.

•  Wear comfortable, good-quality walking or running shoes and 

appropriate clothing. Do not use this unit with bare feet, sandals, 
socks or stockings!

•  Always examine your unit before using to ensure all parts are in 

working order.

•  Do not leave children unsupervised near or on the unit.

•  Service to your unit should only be performed by an authorized  

service representative, unless authorized and/or instructed by a 
Keys Fitness technician. Failure to follow these instructions will void 
the warranty.

NOTE

:

  

Hand tighten bolts and nylon nuts until machine is fully assembled.

Read all precautions and instructions in this manual before using this equipment.  

Summary of Contents for Power System KF-2060

















































Reviews: