manualshive.com logo in svg

Key Automation CT202, Instructions And Warnings For Installation And Use

Share
Download
Key Automation CT202 Instructions And Warnings For Installation And Use Download Page 1

     Centrale per due motori 230 Vac (120 Vac), per cancelli a battente

Control unit for two 230 Vac (120 Vac) motors, for swing gates

Logique de commande pour deux moteurs 230 Vca (120 Vca), pour portails battants

Central para dos motores de 230 Vca (120 Vca) para puertas de batiente

Steuergerät für zwei Drehtor-Motoren 230 Vac (120 Vac) 

Unidade para dois motores 230 Vac (120 Vac), para portões de batente

Centrala dla dwóch silników 230 Vac (120 Vac), do bram skrzydłowych

CT202

Istruzioni ed avvertenze per l’installazione e l’uso

Instructions and warnings for installation and use

Instrucciones y advertencias para su instalación y uso

Anleitungen und Hinweise zu Installation und Einsatz

Instruções e advertências para a instalação e utilização

Instructions et avertissements pour l’installation et l’usage

UP

DOWN

MENU

SS

Management

System

ISO 9001:2008

www.tuv.com

ID 9105043769

Summary of Contents for CT202














Reviews:

No comments

Brands by name

Popular brands

Load more brands