Key Automation 900CT-824S Instruction Manual Download Page 5

15

ENGLISH

CONNECTOR CN3

13) FCC1 

Motor 1 limit switch (closing limit switch) 

14) FCA1 

Motor 1 limit switch (opening limit switch)

15) FCC2 

Motor 2 limit switch (closing limit switch)

16) FCA2 

Motor 2 limit switch (opening limit switch)

17) COMF  Motors 1-2 limit switch common connection

N.B. the LEDs corresponding to the limit switches are ON when the relative limit switch is 

not involved, if the limit switches are not used, they MUST be JUMPERED on the COMF ter

-

minal 

NO PED

NO P/P

NC STOP

COMMON

Accessory supply

3

TX

RX

3 4

NC

F1

3

TX

RX

3 4

NC

F2

1 2

1 2

1 2

1 2

24Vac/dc

-                +

24Vac/dc

-                +

24Vac/dc

-     +

24Vac/dc

-     +

CONNECTOR CN4

18) PED 

Connection of the Pedestrian Function N.O. contact Normally Open

With 2 motor operation, door M1 is opened completely, in the case of a pedestrian opening and at 

the same time, with a step/step P/P impulse, door 2 starts immediately if 2 motors are selected, it 

opens fully if 1 motor is selected. 

19) P/P 

Connection of the Step/Step Function N.O. contact Normally Open

Input of the Open/Close or Open/Stop/Close command based on the selection of Parameter D 

20) F1  

Connection of the Close Photocell F1 N.C. contact Normally Closed

This input is considered a safety, the contact can be interrupted at any time during closing of the 

automation causing an immediate stop in movement and reversing the direction of movement

21) F2  

Connection of the Open Photocell F2 N.C. contact Normally Closed

This input is considered a safety, the contact can be interrupted at any time during opening by the 

automation causing an immediate stop in movement, the automation will continue until the contact 

is restored.

22) CST 

Rib connection Normally Closed contact N.C. 

At each intervention of the photo-rib, the motion will stop and invert for 2 seconds, and will then 

stop, deactivating the automatic closure if activated 

23) STP 

Stop connection Normally Closed contact N.C. 

This input is considered a safety. The contact may be interrupted at any moment immediately stop-

ping the automation disabling any function including automatic closing

24) COM 

Link common commands and of securities

Summary of Contents for 900CT-824S












Reviews: