Lock Tab
Seated Properly
6.
Press and release the Power Switch found
directly behind the right side of the Brewer.
Switch is spring loaded and will return to
original position.
7.
The Blue LCD Control Center will come on and
indicate “NOT READY.”
NOTE:
A K-Cup
®
portion
pack should not be used for this sequence
.
8.
The Brewer will automatically fill the internal
tank with water and then the water will be
heated. This will take about 4 minutes.
During the heating period, “NOT READY”
is displayed on the LCD Control Center (fig. 3).
Do not lift Brewer handle during this ‘heating
period.’
Once the water is heated, “READY TO
BREW” will be displayed (fig. 4).
SECTION 1
Set-Up & First Brew
5.
Place a portion pack in the K-Cup
®
Holder (fig. 6).
CAUTION:
There are two sharp needles that
puncture the portion pack, one above the K-Cup
®
Holder and the other in the bottom of the K-Cup
®
Holder. To avoid risk of injury, do not put your
fingers in the K-Cup
®
Assembly Housing.
6.
Lower the Handle to close the Lid over the
K-Cup
®
Holder. (When it is closed completely,
the LCD Control Center will indicate “READY
TO BREW.” The Left and Right Buttons and
the BREW Button will be illuminated up to
60 seconds.)
a.
All brew size icons are lit with the default
size flashing (fig. 7). To choose a different size,
press Left Button to go down in size or Right
Button to go up in size.
NOTE: The Small Mug is the factory set default
brew size. To program your favorite brew size see
page 14 “Programming Your Brew Size”.
b.
Your choices are a stronger Extra-Small
Cup (3.25 oz. serving), a Small Cup (5.25 oz.
serving), a Small Mug (7.25 oz. serving), a Large
Mug (9.25 oz. serving) or a Travel Mug (11.25 oz.
serving).
NOTE:
You may see small amounts of water coming
from the Vent and dripping into the Water Reservoir
during this and subsequent heating — this is normal.
9.
Lift and lower the Handle. Press the BREW
Button to start a cleansing brew without a
K-Cup
®
portion pack. Pour the hot water
into the sink.
NOTE:
A portion pack should not be used for
this Sequence
.
10.
The one-time set-up process is now
complete and you are ready to brew!
NOTE:
The Brewer may take 15-30 seconds
between brews and then “READY TO BREW”
will be displayed.
Ready to Brew Your First Cup
1.
LCD Control Center will indicate
“READY TO BREW.”
2.
Place a cup or mug on the Drip Tray Plate.
3.
Lift the Handle and the K-Cup
®
Holder
will open toward you (fig. 5).
4.
Select a portion pack.
NOTE:
Do not remove the foil
lid or puncture the portion pack.
MENU
READY
NOT
Setting Up Your Brewer
1.
Unwrap cord and plug the Brewer into a
grounded outlet. Remove all pieces of packing
tape and clear plastic sticker from LCD display.
2.
Place a large mug (10 oz. minimum) on the
Drip Tray Plate.
3.
Remove the Water Reservoir from Brewer by
first removing Lid from the Water Reservoir
(fig. 1), then lifting the Water Reservoir straight
up and toward front of Brewer (may be tight),
(fig. 2 A). Rinse with fresh water.
4.
Fill Water Reservoir with bottled or filtered
water so that the water level is just below the
top edge of the Water Reservoir.
5.
Place Water Reservoir base into the left side of the Brewer and be sure the
Water Reservoir Lock Tab engages with the Brewer. Replace Lid on Water
Reservoir.
NOTE:
Please ensure the Water Reservoir is seated properly, so
that the back of the Water Reservoir is flush with the Brewer (fig. 2 B and C).
IMPORTaNT: You cannot use your Keurig
®
Brewer until it has been set
up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures below freezing,
allow Brewer at least two hours to reach room temperature before
brewing. A frozen or extremely cold Brewer will not operate.
BREW
MENU
MENU
READY
TO BREW
fig.
3
fig.
4
fig.
6
fig.
1
fig.
5
fig.
7
6
7
fig.
2
a
B
Not Seated Properly
C
