KEUCO 33098 XX1550, Instructions For Use Manual

Page: 4 / 12

4
US
Important information, please make sure to read!
Technical data
– Power supply: 230 V AC/ 50 Hz
– max. Power consumption:
Prod. no.: Width Weight Light Heating
33098 XX1550: 19-11/16''
(500)
20,94 lb
(9.5 kg)
27 W 26 W
33098 XX2050: 25-19/32''
(650)
25,13 lb
(11.4 kg)
30 W 41 W
33098 XX2550: 31-1/2''
(800)
29,32 lb
(13.3 kg)
33 W 52 W
33098 XX3050: 38-3/4''
(1000)
35,05 lb
(15.9 kg)
42 W 65 W
33098 XX3550: 47-1/4''
(1200)
40,57 lb
(18.4 kg)
48 W 82 W
– Protection rating: IP20
– Ambient conditions:
Temperature 41° – 104° F
– Light colour 2700 - 6500 Kelvin
Mounting dimensions , see pages 2.
Circuit diagram , see figure 1 on page 7.
Installation
, see figure 2 onwards on page 7.
Operation
The mirror can be optionally actuated similar to a toggle
switch with a button on the mirror (A) or with an external
light switch (B), see circuit diagram figure 1 on page 7.
A
B
Button functions
Button Function
Light on/off
• Pressing the button switches the mirror on with the
selected settings. The white LED goes off.
• Pressing the button again switches the mirror off.
The white LED lights up.
• The white LED can be deactivated.
– Switch on the mirror.
– Press and hold the button for 10 seconds.
-The lighting goes off.
-A short light impulse indicates that the white
LED was deactivated.
To switch the white LED back on, repeat the de-
scribed procedure.
Button Function
Front and wall lighting
• The front and wall lighting is switched on by press-
ing the button when mirror is switched on.
• Pressing the button again switches the light off.
Washbasin lighting
• The washbasin lighting is switched on by pressing
the button when mirror is switched on.
• Pressing the button again switches the light off.
When both lightings are switched off, the mirror also
switches off.
Dimming the front, wall and washbasin lighting
• Press the button when the mirror is switched on
and hold until the desired brightness or the end
value has been reached.
The setting is stored and reproduced when switched
on again (only for connection type 1, see figure 1 on
page 8).
Setting the light colour cooler
• Press and hold daylight white button and the light
colour fades to cool white.
• Release when the desired light colour has been
reached.
The setting is stored and reproduced when switched
on again (only for connection type 1, see figure 1 on
page 8).
Adjusting light colour - daylight white (cool white)
• Press button and the colour temperature sets to
6500 Kelvin.
Setting the light colour warmer
• Press and hold warm white button and the light
colour fades to warm white.
• Release when the desired light colour has been
reached.
The setting is stored and reproduced when switched
on again (only for connection type 1, see figure 1 on
page 8).
Adjusting light colour - warm white
• Press button and the colour temperature sets to
2700 Kelvin.
Heating on/off
• Press button and the red LED lights up.
• Pressing the button again switches the heating off,
and the red LED goes out.
The heating switches off automatically after 20
minutes.
Replacement parts with order numbers , see pages 10
and 11.
The light sources may only be replaced by the
manufacturer, its customer service or by an equally
qualified person.
For information about warranty and maintenance, see
the enclosed Maintenance and Warranty Passport .
Disposal information! Equipment with this labelling
must not be disposed of in household refuse, but must
be disposed of at a collection centre intended for this
purpose.