PAGE 13
X2
INSTALLATION GUIDE
770-000026-01 r08
INSTALLATION
INCANDESCENT DIMMER
X2-INC
INCANDESCENT DIMMER
New Construction
1.
Install wall box (single gang wall box with at least 14 in3 cubic inch volume only).
2.
Run power to wall box utilizing stranded or solid core 12-18 AWG wire.
(See Fig 1)
3.
Prepare the wire for connection to lead wire: A. Strip 8.5 mm of wire for insertion into the wire nut. B.
Twist the stranded wire to prevent fraying (tinning optional).
4.
Using the provided wire nuts, attach each X2 lead wire to the corresponding conductor. Black-Line,
White-Neutral, Green-Ground, Red-Dimmed Line.
(See Fig 2 & 3)
Warning
- Do not connect Dimmed Line (Red) to AC Input Line (Black)
5.
Ensure that no conductors are visible after insertion, and that no stray wires are exposed.
6.
Carefully tuck wires back into wall box.
120V~
50/60 HZ
X2 KEYPAD - INC
I N C
PAGE 12
X2
INSTALLATION GUIDE
770-000026-01
PAGE 13
X2
INSTALLATION GUIDE
770-000026-01
11. Energize circuit.
Note: Indicator lights will power on if unit is properly wired.
12.Installation is complete. Refer to Design Studio Software for
commissioning details.
Retrofit
Important Notes:
•
This wiring scheme is for standard in-line 2-Way light switches.
•
Wall box should have volume of 14 in
3
or greater.
•
The X2 Keypad and Ketra products require a constant, uninterrupted
source of electricity. Power needs to be run directly to fixtures being
controlled by the X2 Keypad. Ketra fixtures to be controlled by the X2
Keypad do not have to be connected to the same circuit, as the
control signal is wireless.
1. Turn off power feed to the switch to be replaced.
2. Remove existing switch.
3. Continue with step 3 in the New Construction section for the AC-input
non-dimming model, Page 11.
INSTALL ATION
(AC INPUT NON DIM)
INSTALL ATION
(ELV DIMMER)
X2-__-ELV-JB-1-__-____
New Construction
1. Install wall box (single gang wall box with at least 14 in
3
cubic inch
volume only).
2. Run power to wall box utilizing stranded or solid core 12-18 AWG wire.
(See Fig 1)
2
1
3. Prepare the wire for connection to lead wire: a. Strip 8.5 mm of wire
for insertion into the wire nut. b. Twist the stranded wire to prevent
fraying (tinning optional).
11
PAGE 12
X2
INSTALLATION GUIDE
770-000026-01
PAGE 13
X2
INSTALLATION GUIDE
770-000026-01
11. Energize circuit.
Note: Indicator lights will power on if unit is properly wired.
12.Installation is complete. Refer to Design Studio Software for
commissioning details.
Retrofit
Important Notes:
•
This wiring scheme is for standard in-line 2-Way light switches.
•
Wall box should have volume of 14 in
3
or greater.
•
The X2 Keypad and Ketra products require a constant, uninterrupted
source of electricity. Power needs to be run directly to fixtures being
controlled by the X2 Keypad. Ketra fixtures to be controlled by the X2
Keypad do not have to be connected to the same circuit, as the
control signal is wireless.
1. Turn off power feed to the switch to be replaced.
2. Remove existing switch.
3. Continue with step 3 in the New Construction section for the AC-input
non-dimming model, Page 11.
INSTALL ATION
(AC INPUT NON DIM)
INSTALL ATION
(ELV DIMMER)
X2-__-ELV-JB-1-__-____
New Construction
1. Install wall box (single gang wall box with at least 14 in
3
cubic inch
volume only).
2. Run power to wall box utilizing stranded or solid core 12-18 AWG wire.
(See Fig 1)
2
1
3. Prepare the wire for connection to lead wire: a. Strip 8.5 mm of wire
for insertion into the wire nut. b. Twist the stranded wire to prevent
fraying (tinning optional).
12
3
