74 / 148
Aide au diagnostic
2019/04
7
Aide au diagnostic
Attention : danger de tension électrique en ouvrant le boîtier du gestionnaire. Les travaux sur les composants
électriques demeurent réservés au domai2.2de compétence d‘électriciens qualifiés (voir 2.2).
Affichage des pannes Cause
Mesure d’arrêt
Remarques
Panne de batterie
La batterie manque ou est
défectueuse
Retirer la fiche de secteur, connecter
les batteries, si nécessaire les
remplacer par de nouvelles
batteries.
La disponibilité fonctionnelle de
l’appareil est montrée par un
nouveau défilement lumineux.
initialisation : l’installation peut être
mise en service, c’est à dire qu’elle
est capable de fonctionner. L’alarme
peut être acquittée.
- exploitation : le message de panne
est affiché au plus tard 5 minutes
après. L’installation est prête à
fonctionner ; le service manuel est
possible..
Panne de moteur
- initialisation : ligne de
commande « Moteur » non
connectée, panne de pole ou
rompue
- Durant l’exploitation : ligne
de commande « Moteur »
défectueuse
Retirer la fiche de secteur,
déconnecter la batterie ; contrôler
le bon raccordement de la ligne de
commande et/ou son passage, le
cas échéant, changer le moteur.
Fault detection only takes place La
détection de pannes ne se fait que
pendant l’exploitation (voir 8.2). -
initialisation : mise en service non
possible - pendant l’exploitation :
détection de pannes en cas de service
manuel, cycle d’essai / refoulement
Sonde en panne
- initialisation : ligne de
commande « Sonde » non
connectée, panne de pole ou
rompue - Durant l’exploitation :
ligne de commande « Sonde »
défectueuse
Retirer la fiche de secteur,
désactiver la batterie ; contrôler le
bon raccordement de la ligne de
commande et/ou son passage, le
cas échéant, changer la sonde.
L’interrogation de la conduite de
sonde a lieu toutes les 2 secondes.
Panne de clapet
Le clapet peut, lors de la
mise en service, et/ou avec la
touche « Contrôle » ne pas être
complètement fermé, c’est à
dire que le clapet est bloqué
par un objet dans le clapet
antirefoulement.
- Mauvaise position du levier
lors du montage du couvercle
Retirer la fiche de secteur,
désactiver la batterie ; ouvrir le
couvercle du Staufix, éliminer le
blocage et remettre l’installation en
fonctionnement
Recommandation : Informer le
revendeur spécialisé
Attention : contrôler la position de
l’obturateur de service ! La commande
essaie par 3 x fois de fermer le clapet
et d’éliminer ainsi éventuellement
l’objet qui bloque le système. Si l’objet
peut être éloigné par le mouvement
du clapet pendant ces cycles,
l’installation est capable de fonctionner
à nouveau. Si cette manoeuvre ne
réussit pas, l’installation tombe en
panne. La confirmation d’ordre du
signal acoustique est possible. Il est
également possible que l’objet soit
évacué en rinçant la conduite. Il est
possible de le vérifier en appuyant
sur la touche de contrôle. En cas de
résultat négatif, le message de panne
est à nouveau généré ; l’objet doit
alors être éliminé en procédant de la
manière décrite ci-dessous.
- Un refoulement a été détecté.
Cependant le clapet ne pas être
complètement fermé, c’est à
dire que le clapet est bloqué par
un objet dans le clapet anti-
refoulement « Panne de clapet
durant le refoulement »
Fermer la vanne batardeau. Après la
fin du refoulement retirer le blocage
tel que décrit
Nombre maximal
de cycles du clapet
dépassé
Max. number of cycles for flap
exceeded
Changer le moteur
Durée de vie du moteur atteinte
Contact flottant ne
passe pas
pas activé
cisaillement defect
Interrupteur
Électricien Specialist