background image

22 

Fault cause and their rectification 

11  Fault cause and remedy

 

This chapter describes in more detail the most important faults which can occur during operation 
on the self-propelled implement. Faults which require major intervention must always be rectified 
by your specialist workshop. 

Observe safety instructions! 

Malfunction: 

  Possible causes: 

Remedy: 

Benzin Motor: 

Gasoline 
engine does 
not start 

-  Spark plug connector not plugged.

-  Motor-off switch on "0"

- Safety circuit not in

Start position

-  Fuel tank emply or

bad fuel

-  Clogged fuel line

-  Spark plug defective

-  Engine too much fuel (flooded)

-  Motor off line defective

-  False air due to lose carburetor

Insert plug connector 

Move choke lever to choke position 

Switch motor off switch to position "I"

 

Bring safety circuit into starting position

Fuel tank with fresh fuel

 füllen 

Fuel tank with fresh fuel
Clean, adjust or replace the spark plug

 

Dry the spark plug, clean and start with 
FULL GAS
Check line and connections
Tighten fixing screws

and suction line

Gasoline Engine 

- Engine is running in the CHOKE area  Move the choke lever to the operating position

hat Aussetzer 

- Ignition cable loose

Plug the spark plug connector firmly onto the 
ignition cable. Clamp the ignition cable 
attachment 

- Fuel line clogged, or

Fit the spark plug plug firmly onto the spark 
plug. Change fuel filter or fresh. 

Bad fluel

- Ventilation in the fuel tank cover

Refuel your fuel 
Replace fuel tank cover 

congested

- Water or dirt in the fuel system
- Air filter dirty

 Drain and clean the fuel, refuel with fresh 
 fuel Clean or replace the air filter 

- Carburetor adjusted

Adjust carburetor 

Benzin-Motor 

- Too little engine oil

Immediately refill engine oil 

gets too hot 

- Cooling air system restricted
- Air filter dirty

Clean fan grille, internal 

Clean cooling fins 

Clean or replace the air filter 

- Carburettor not set correctly

Adjust carburetor 

Benzin-Motor 

- Ignition distance too low

Adjust spark plug 

has dropouts 
at high speeds 

- Idle mixture not corrects

adjusted

Adjust carburetor 

 Zahlen 

Gasoline engine 

often idles 

out 

- Ignition distance too high,

Spark plug defective

- Carburettor not set correctly

  Set or replace spark plug

Adjust carburetor 

- Air filter dirty

Clean or replace the air filter 

Summary of Contents for B00002





























Reviews: