ENGLISH
7
7
ENGLISH
OPERATION
CAUTION : Always make sure that there is suf cient ventilation.
SET CLOCK
It is only possible to set the correct time, when the
heater is connected to the mains and not burning.
1. Use the Adjustment Keys ( hour / min.) to
set the time.
2. To set the time, press “hour” and “min.” set but-
tons. Individual motions will increase the time by
one unit; holding continuously will raise either the
“hour” or “min.” rapidly. After approximately 10
seconds the blinking will stop and the setting will
be locked. 5 Minutes after switching off the heater,
the information on the display will disappear and
the heater will automatically switch into the stand-
by position.
IGNITION
1. Just press the button to ignite the heater. The
button will start blinking, indicating that the ignition
procedure has started. This will take a short while.
2. After this time heater will automatically ignite and
The button will cease its ashing. The Operation
Lamp will remain alight so long as heater is burn-
ing.
NOTE: If using your heater for the rst time, or after long term storage, ignition may not take place
on the rst try. Press the button again.
NOTE: Fuel pump may produce an audible operating noise at ignition. This is only temporary.
7
ENGLISH
OPERATION
CAUTION : Always make sure that there is suf cient ventilation.
SET CLOCK
It is only possible to set the correct time, when the
heater is connected to the mains and not burning.
1. Use the Adjustment Keys ( hour / min.) to
set the time.
2. To set the time, press “hour” and “min.” set but-
tons. Individual motions will increase the time by
one unit; holding continuously will raise either the
“hour” or “min.” rapidly. After approximately 10
seconds the blinking will stop and the setting will
be locked. 5 Minutes after switching off the heater,
the information on the display will disappear and
the heater will automatically switch into the stand-
by position.
IGNITION
1. Just press the button to ignite the heater. The
button will start blinking, indicating that the ignition
procedure has started. This will take a short while.
2. After this time heater will automatically ignite and
The button will cease its ashing. The Operation
Lamp will remain alight so long as heater is burn-
ing.
NOTE: If using your heater for the rst time, or after long term storage, ignition may not take place
on the rst try. Press the button again.
NOTE: Fuel pump may produce an audible operating noise at ignition. This is only temporary.
1
2
2. To set the time, press “hour” and “min.” set
keys. Individual motions will increase the
time by one unit; holding continuously will
raise either the “hour” or “min.” rapidly. After
approximately 10 seconds the blinking will stop
and the setting will be locked. 5 Minutes after
switching off the heater, the information on
the display will disappear and the heater will
automatically switch into the stand-by position.
1. Just press the
key to ignite the heater. ON/
OFF Lamp will start blinking, indicating that the
ignition procedure has started. This will take a
short while.
2. After this time heater will automatically ignite
and ON/OFF Lamp will cease its flashing. ON/
OFF Lamp will remain alight so long as heater is
burning.
NOTE: If using your heater for the first time, or after long term storage, ignition may not take
place on the
fi
rst try. Press the key again.
NOTE: Fuel pump may produce an audible operating noise at ignition. This is only temporary.
Summary of Contents for LC-45
