manualshive.com logo in svg

KERN OPTICS OKO 178, Operating Instructions Manual

Share
Download
KERN OPTICS OKO 178 Operating Instructions Manual Download Page 27

OKO-1-BA-en-2111 

 

26 

9  Troubleshooting  

 

Problem 

Possible causes 

Lamp does not burn 

Mains plug not inserted correctly 

No power available at the socket 

Lamp defective 

Fuse defective 

Field of view is dark 

Aperture diaphragm and/or field diaphragm 

are not open wide enough 

The beam path selection slider is set to 

"Camera". 
The condenser is not properly centered 

Brightness cannot be regulated 

The brightness control is set incorrectly 

The condenser was not centered correctly 

The condenser is lowered too far 

Field of view is dark or not correct  

floodlit 

The lens was not swiveled in properly 
The beam path selector slide is in an 

intermediate position 
The object turret is not mounted correctly 

The condenser is not mounted correctly 
A lens is used that does not match the 

illumination range of the condenser. 
The condenser was not centered correctly 

The light field diaphragm is closed too far 

The lamp is not mounted correctly 

The field of vision of one eye does not 

match that of the other eye 

The interpupillary distance is not adjusted 

correctly 

The diopter adjustment has not  been made 

correctly 

Different eyepieces are used on the right and 

left 

The eyes are not used to microscopy 

 

 

Summary of Contents for OPTICS OKO 178






























Reviews:

No comments

Brands by name

Popular brands

Load more brands