background image

KEPCO, INC. 

   

 131-38 SANFORD AVENUE 

 

  FLUSHING, NY. 11355 U.S.A.

 

  TEL (718) 461-7000

   

 FAX (718) 767-1102

  

http://www.kepcopower.com   

 

 email: [email protected]

 083013

228-1568 REV 8

7

FIGURE 7.  HSF-1UR 100W POWER SUPPLY OUTLINE DRAWING

3.755 [95.4]

0.690 [17.5]

0.156 [4.0]

4.275 [108.6]

1.406 [35.7]

0.133 [3.4]

1.108 [28.2]

0.250 [6.4]

0.140 [3.6]

0.066 [1.7]

0.125 [3.2]

INSERT JUMPER J1

CONNECTOR

FAN

3010294

DETAIL "B"

SEE DETAIL "A"

JP1

MAX MOUNTING 

TORQUE:
2 IN.-LBS (0.23 N x m)

0.140 [3.6]

0.250 [6.4]

7. FOR CONVECTION COOLING, DISCONNECT FAN AND

     INSERT JUMPER (P/N 172-0382) AS SHOWN IN DETAIL "B."

4. DIMENSIONS ARE IN INCHES, [DIMENSIONS IN BRACKETS 
    ARE IN MILLIMETERS].
5. TOLERANCES (UNLESS OTHERWISE SPECIFIED):
     3 PLACES: ±0.005, 2 PLACES: ±0.01, FRACTIONS: ±1/64"

SEE DETAIL "B"

1.732 [44.0]

0.010 [0.3]

4.295 [109.1]

0.140 [3.6]

0.076 [1.9]

1.131 [28.7]

0.471 [12.0]

0.780 [19.8]

3.960 [100.6]

0.437 [11.1]

1.474 [37.4]

0.591 [15.0]

B) PCB 0.063" THK FR-4

6. TO DISABLE FORCED SHUTDOWN UPON FAN 
     FAILURE, INSERT JUMPER (P/N 172-0382) AS 
     SHOWN IN DETAIL "B."

3. MODULE IS KEYED AS SHOWN IN DETAIL 

A) BACKPLATE 0.064" THK. ALUM. 5052-H32

C) FRONT PANEL 0.090 THK. ALUM. 6061-T6

 FRONT PANEL -KEPCO DUAL TONE GRAY

1. MATERIAL:

2. FINISH:

NOTES:

 

0.750 [19.1]

1.125 [28.6]

JP1

0.260 [6.6]

0.282 [7.2]

0.503 [12.8]

13.050 [331.5]

0.507 [12.9]

1.088 [27.6]

KEY PIN LOCATION

12 VOLTS 

15  VOLTS 

24 VOLTS

DETAIL "A"

0.140 [3.6]

3.3 VOLTS

5 VOLTS 

0.228 [5.8]

48 VOLTS

28 VOLTS

0.190

[4.8]

0.191 [4.9]

14.131 [358.9]

0.125 [3.2]

0.129 [3.3]

0.303 [7.7]

0.391

[9.9]

0.507
[12.9]

1.732
[44.0]

Summary of Contents for HSF 3.3-25-1UR








Reviews: