HSF (M) 600W 042315
3
FIGURE 2. POWER RATING VS. TEMPERATURE (INPUT: 95 TO 264V A-C)
TABLE 2. OUTPUT RATINGS AND SPECIFICATIONS
MODEL
HSF 12-53*
HSF 15-43*
HSF 24-27*
HSF 28-23*
HSF 48-13*
Output Volts d-c (nominal)
12
15
24
28
48
Output
Adjustment
Range
(1)
Using front panel trim
pot
(Volts d-c)
M
9 to 13.8
11.5 to 17.4
17 to 28.2
21.5 to 33
35 to 52.2
MZ
(2)
0 to 13.8
0 to 17.4
0 to 28.2
0 to 33
0 to 52.2
Using Voltage source or external 5K
ohm Trimpot (Volts d-c)
(2)
0 to 13.8
0 to 17.4
0 to 28.2
0 to 33
0 to 52.2
Output Current (nominal) (Amps)
53
(3)
43
(3)
27
23
13
Maximum Output Power (Watts)
(4)
636
(3)
645
(3)
648
644
624
Overcurrent Setting (Amps)
(5)
55.6-68.9
45.1-55.9
28.3-35.1
24.1-29.8
13.7-16.9
Short Circuit Current (Amps)
65
55
35
29
19
Overvoltage Protection (OVP) (Volts d-c)
(6)
14.3 - 16.8
18.0 - 21.0
29.3 - 33.6
34.2 - 39.2
54.5 - 59.8
Efficiency
(% typ.)
AC Input 100V
80
81
82
82
84
AC Input 200V
84
85
86
86
87
Power Factor
(typ.)
AC Input 100V
0.99
0.99
0.99
0.99
0.99
AC Input 200V
0.95
0.95
0.95
0.95
0.95
Ripple &
Noise
(7)(8)
ripple (mV, p-p)
180
180
220
220
220
ripple noise (mV, p-p)
220
220
320
320
320
Minimum output voltage requirement (V)
7.2
10.5
16.8
19.6
39.6
Sense Resistor (IMON) values (Ohms)
0.002
0.005
0.01
0.01
0.02
*
Unless otherwise noted, specifications apply to both M and MZ models.
(1)
M Models only
: To adjust output voltage down to approximately 0V use external voltage source or resistance (see PAR. 3.4.2).
Refer to Table 4 for minimum conditions required to maintain proper operation of alarm relay, meter and visual LED indicator.
MZ Models only
: If the visual LED indicator is powered from the HSF output (see PAR 3.4.3), refer to Table 5 for minimum
conditions required to maintain functionality of the indicator.
(2)
Output specifications may not be met if voltage adjusted below values shown for M models.
(3)
For 100V a-c input, maximum output current for 12V model: 50A (600W), for 15V model: 40A (600W).
(4)
See Figure 2 for power derating.
(5)
Square type. Output voltage returns automatically only if cause is removed within 30 seconds (see PAR. 3.7.2).
(6)
When overvoltage is detected, output is shut OFF. Recovery is by removing, and after approximately 40 seconds, reapplying
AC input power or by reset (open and close) at ±RC terminals (no delay).
(7)
Ripple and noise levels above are satisfied when conditions are 0 to 100% load, 0 to 40°C (load is derated from 40 to 55°C,
see Figure 2), and bandwidth
100MHz.
(8)
Minimum output voltage required to meet ripple, noise and stabilization (see Table 3) specifications.
NOTE:
Safety agency approvals
apply only to operation
between -10°C and 40°C.
