TM-V71A/V71E
42
4) Check the PTT signal operation.
q
Input 5 to 10 V to pin 2 of the transceiver PC terminal
or pin 7 of the PG-5H D-SUB terminal (CTS).
w
Ensure that the transceiver becomes the transmission
state.
5) Check the voice operation.
q
Connect the data communications cable (6-pin mini
DIN terminal and pink/ green pin) of the PG-5H
(Interface cable kit) to the DATA terminal on the rear
of the transceiver.
w
Input a 1kHz/ 150 mV AF signal from AG to the green
pin of the data communication cable (PKD line).
Confi rm the modulation of 2 to 4 kHz deviation hangs
when transmitting by PTT operation as stated in step
4), above.
e
Input a standard modulation signal of -47dBm (MOD:
1kHz, DEV: 3kHz, and AF output: 0.63V/8
Ω
) from SSG
to the transceiver.
Check that a 1kHz tone of 3 to 15 mV is output from
the pink pin (PR1 line) of the data communication
cable.
PG-5H
Data communications cable pin configuration
PR1 line: To microphone input terminal
PKD line: To line out terminal
Adjustment Mode
This mode is used to replace or readjust IC916 (EEPROM).
In Adjustment Mode, the transceiver can be adjusted using
its panel keys.
■
Adjustment Items
1. Frequency (Band A)
2. Frequency (Band B)
3. High power (144MHz band, 430MHz band)
4. Mid power (144MHz band, 430MHz band)
5. Low power (144MHz band, 430MHz band)
6. SWR protection (144MHz band, 430MHz band)
7. DCS balance (Band A) (144MHz band, 430MHz band)
8. DCS balance (Band B) (144MHz band, 430MHz band)
9. MAX deviation (Band A) (144MHz band, 430MHz band)
10. MAX deviation (Band B) (144MHz band, 430MHz band)
11. CTCSS deviation (Band A) (144MHz band, 430MHz
band)
12. CTCSS deviation (Band B) (144MHz band, 430MHz
band)
13. DCS deviation (Band A) (144MHz band, 430MHz band)
14. DCS deviation (Band B) (144MHz band, 430MHz band)
15. BPF RSSI (Band A) (144MHz band, 200MHz band,
430MHz band)*1
16. BPF RSSI (Band B) (144MHz band, 200MHz band,
430MHz band)*1
17. Squelch threshold (Band A) (144MHz band, 200MHz
band, 300MHz band, 430MHz band)
18. Squelch threshold (Band B) (144MHz band, 200MHz
band, 300MHz band, 430MHz band, 1.2GHz band)
19. Squelch tight (Band A) (144MHz band, 200MHz band,
300MHz band, 430MHz band)
20. Squelch tight (Band B) (144MHz band, 200MHz band,
300MHz band, 430MHz band, 1.2GHz band)
21. S-meter S1 (Band A) (144MHz band, 200MHz band,
300MHz band, 430MHz band)
22. S-meter S1 (Band B) (144MHz band, 200MHz band,
300MHz band, 430MHz band, 1.2GHz band)
23. S-meter full scale (Band A) (144MHz band, 200MHz
band, 300MHz band, 430MHz band)
24. S-meter full scale (Band B) (144MHz band, 200MHz
band, 300MHz band, 430MHz band, 1.2GHz band)
*1: Adjust 3 points (Low, Center, High) for the 144MHz band
and the 200MHz band.
Adjust 5 points (Low, Low’, Center, High’, High) for the
430MHz band.
■
How to enter the adjustment mode
1. Tu r n t h e t r a n s c e i v e r p o w e r O F F a n d i n s e r t t h e
adjustment jig (W05-0611-00) into the DATA terminal
located on the rear panel of the transceiver.
2. Turn the transceiver power ON while pressing the [CALL]
and [F] keys to enter adjustment mode.
3. The adjustment item ”FRQ A” of the Band A frequency
is displayed when entering the adjustment mode.
Blink
Note:
• To exit the Adjustment Mode, turn the transceiver power
OFF.
• When the adjustment mode is activated, the transceiver
automatically sets the frequency as shown in ”The
frequency that is set to the transceiver” table, on pages
44 to 46.
■
LCD display in the adjustment mode
The value stored in the EEPROM (0~254)
RSSI value
Current adjustment value (0~254)
Adjustment band item
Adjustment item
ADJUSTMENT