12
TK-860G/862G
Note :
You can clone the programmed data between the trans-
ceiver listed below. Frequency version must be same.
Slave TK-360G TK-360G TK-360G TK-360G TK-860G TK-860G TK-860G
K
M
K4
M4
K
M
K3
TK-370G TK-370G TK-370G TK-370G TK-862G TK-862G
Master
K
M
K4
M4
K
M
TK-860G
YES
NO
NO
NO
YES
NO
NO
K
TK-860G
NO
YES
NO
NO
NO
YES
NO
M
TK-860G
NO
NO
YES
NO
NO
NO
YES
K3
REALIGNMENT
Cloning cable
(E30-3382-05)
Fig. 2
MBL
PSB
GND
PTT/TXD
ME
MIC
HOOK/RXD
CM
GND
REMOTE/TXD
PTT/RXD
8
1
1
8
Clone cable
E30-3411-05 (TK-860G
→
TK-360G/370G)
8. Self Programming Mode (TK-860G only)
Write mode for frequency data and signalling etc. Mainly
used by the person maintaining the user equipment.
8-1. Enter to the Self Programming Mode
Remove D507 (Figure 3) from the TX-RX unit. Hold down
the [A] key and turn the power switch on. When enter the
self programming mode, "SELF" is displayed. The mode
changes autoically to Model Select Mode in about one sec-
ond, and set up radio type, radio band & channel type and
frequency version.
Notes :
• To start the Firmware Programmer from KPG-56D, the
FPRO path must be set up by the KPG-56D setup.
• This mode cannot be entered if the Firmware program-
ming mode is set to Disable in the Programming soft-
ware (KPG-56D).
• When programming the firmware, it is recommend to
copy the data from the floppy disk to your hard disk be-
fore you update the radio firmware.
Directly copying from the floppy disk to the radio may not
work because the access speed is too slow.
6-4. Function
1. If you press the [MON] switch while "PROG 576" is dis-
played, the checksum is displayed. If you press the
[MON] switch again (while the checksum is displayed),
"PROG 576" is redisplayed.
2. If you press the [A] switch while "PROG 576" is displayed,
the display changes to "PROG 192" to indicate that the
write speed is low speed (19200 bps). If you press the
[A] switch again while "PROG 192" is displayed, the dis-
play changes to "PROG 384", and the write speed be-
comes the middle speed (38400 bps). If you press the
[A] switch again while "PROG 384" is displayed, the dis-
play returns to "PROG 576".
Note :
TK-862G indicate
19200 bps : The LED flashes green and red alternately.
38400 bps : The LED flashes orange.
57600 bps : The LED lights orange.
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one radio to
another by connecting them via their modular microphone
jacks. The operation is as follows (the transmit radio is the
master and the receive radio is the slave).
1. Turn the master TK-860G power ON with the [
] key
held down. The TK-860G displays "CLONE".
2. Power on the slave TK-860G/862G.
3. Connect the cloning cable (No. E30-3382-05) to the
modular microphone jacks on the master and slave.
4. Press the [SCN] key on the master while the master dis-
plays "CLONE". The data of the master is sent to the
slave. While the slave is receiving the data, "–PC–" is dis-
played. When cloning of data is completed, the master
displays "END", and the slave automatically operates in
the User mode. The slave can then be operated by the
same program as the master.
5. The other slave can be continuously cloned. When the
[SCN] key on the master is pressed while the master dis-
plays "END", the master displays "CLONE". Carry out the
operation in step 2 to 4.
