Kenwood NX-300K Instruction Manual Download | Manualshive

Page: 4 / 11

background image

NX-300-K, NX-300-K3, TK-5320-K, TK-5320-K3

FCC ID: ALH378500

Installing the Antenna

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and
turning it clockwise until secure.

Installing the Belt Clip

If necessary, attach the belt clip using the two supplied 3 x 6 mm screws.

Notes:

If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting

in a hot environment.

«
...
2
3
4
5
6
...
»

Summary of Contents for NX-300K












Reviews:

No comments

Related manuals for NX-300K

Brand: Bush Pages: 9

Brand: TechniSat Pages: 267

Brand: Blue-Links Pages: 10

Brand: Uniden Pages: 84

Brand: Cobra Pages: 2

Brand: Cobra Pages: 11

Brand: JBL Pages: 4

Brand: Kienzle Automotive Pages: 44

Brand: UNIMO Technology Pages: 10

Brand: Hyundai Pages: 56

Brand: PERFECTPRO Pages: 191

Brand: Puxing Pages: 16

Brand: Radioddity Pages: 24

Brand: Medion Pages: 45

Brand: Icom Pages: 56

Brand: Advanced Wireless Communications Pages: 46

Brand: ALDI Pages: 32

Brand: auna Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands