background image

 

NX-300-K, NX-300-K3, TK-5320-K, TK-5320-K3 

FCC ID: ALH378500 

 
 

 

OPERATING BASICS

ATING BASICS 

 

§    Switching Power ON/OFF 

Turn the 

Power 

switch/ 

Volume 

control clockwise to switch the transceiver ON. 

Turn the 

Power 

switch/ 

Volume 

control counterclockwise to switch the transceiver OFF. 

 

§    Adjusting the Volume 

Rotate the 

Power 

switch/ 

Volume 

control to adjust the volume.   

 

§  Selecting a Channel 

Pressing [<B], [C>]

 

to select a channel. 

Pressing [C>] increases the channel number and pressing [<B] decreases it. 

 

§  Making a Call 

Select the desired channel. 

Press the 

Side1 

key (Programmed function Squelch off) to determine whether or not the current channel is being 

used. 

• If the channel is busy, wait until it becomes free. 

Press and hold the 

PTT 

switch, then speak into the microphone in your normal voice. 

• For best results, hold the microphone approximately 3 to 4 cm (1 1/2 inches) from your lips. 

Release the 

PTT 

switch to receive. 

 

AUXILIARY FEATURES 

 

§  Time-out Timer (TOT) 

The TOT is used to automatically inhibit transmission after a specified time elapse. If the PTT switch is held down for 
longer than specified time, the transceiver will stop transmitting and a tone will sound. Release the PTT switch, then 
press it again to continue transmitting. 

Summary of Contents for NX-300K












Reviews: