18
EN
Preparing for surround sound
6
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• In step
6
and
7
, indications appear only for the selected channels
of the speakers that require adjusting.
1
Press the SETUP key to begin TEST TONE.
• This model enters the speaker volume level adjustment mode.
The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or MULTI CONTROL
%
/
fi
keys.
1
AUTO
2
MANUAL
2
Press the SETUP key again to select either “AUTO” or
“MANUAL”.
Use the MULTI CONTROL knob or MULTI CONTROL
%
/
fi
keys
to adjust the volume level of the test tone output from the
speaker channel to be adjusted.
For “AUTO” selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
º
• If any of the speaker is set as OFF during SP SETUP, the TEST
TONE adjustment for the speaker will be skipped.
(KRF-V6100D only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB” and “LB” are not appeared but “BS” is appeared on the
display.
3
Press the SETUP key.
• The test tone is turned off. This model enters the mode for
inputting the distance to the speakers.
4
For “MANUAL” selection, press the SETUP key each time to
select the speaker channel.
7
Input the distance to the speakers.
1
Select the “DISTANCE” from the setup displays and press the
SETUP key again.
2
Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers:
Distance to Front Left speaker (L)
: ____ feet (meters)
Distance to Center speaker (C)
: ____ feet (meters)
Distance to Front Right speaker (R)
: ____ feet (meters)
Distance to Surround Right (RS)
: ____ feet (meters)
Distance to Surround Back Right (RB): ____ feet (meters)
Distance to Surround Back (BS)
: ____ feet (meters)
Distance to Surround Back Left (LB) : ____ feet (meters)
Distance to Surround Left (LS)
: ____ feet (meters)
Distance to Subwoofer (SW)
: ____ feet (meters)
(KRF-V6100D only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB”/ ”RIGHT BACK SURR” and “LB”/ ”LEFT BACK SURR” are
not appeared but ”BS” / “BACK SURR” is appeared on the display.
3
Use the MULTI CONTROL knob or MULTI CONTROL
%
/
fi
keys
to select the distance to the Front speakers.
Indication in feet
Indication in meters
• The allowable setting range is 1 to 30 feet (0.3m to 9.0m),
adjustable in 1 foot (0.3m) increments.
4
Press the SETUP key to accept the settings.
5
Repeat steps
3
and
4
to input the distance for each of the
speakers.
8
Adjust the LFE LEVEL (Low Frequency Effects level)
1
Select the “LFE LVL” from the setup displays and press the
SETUP key again.
2
Use the MULTI CONTROL knob or MULTI CONTROL
%
/
fi
keys
to adjust the LFE LEVEL.
• The LFE LEVEL is adjusted from 0dB to -10dB in 1dB step
decrements.
3
Press the SETUP key to accept the setting.
4
Setup is complete when the “EXIT” indication appears.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
5
Press the SETUP key to exit the SETUP mode.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
1
Use the INPUT SELECTOR knob to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
2
Press the SOUND key repeatedly until the “INPUT” indication
appears.
3
Use the MULTI CONTROL knob or MULTI CONTROL
%
/
fi
keys to
adjust the input level.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4
Press the SOUND key again to return to the input indication.
5632_16_25_EN
06.4.20, 2:00 PM
18
