ENGLISH
27
Data Size:
B6L (182 mm x 128 mm)
Book Size:
B6L (182 mm x 128 mm)
Default:
[XX]
[DISPLAY]
[COLOR SELECT]
Selects illumination colors for
[ALL ZONE]
,
[ZONE 1]
and
[ZONE 2]
separately.
1
Select a zone. (See the illustration on page 26.)
2
Select a preset color for the selected zone. (Page 31)
Default:
[VARIABLE SCAN]
To make your own color, select
[CUSTOM R/G/B]
. The color you have made
will be stored in
[CUSTOM R/G/B].
1
Press the volume knob to enter the detailed color adjustment.
2
Press
S
/
T
to select the color (
[R]
/
[G]
/
[B]
) to adjust.
3
Turn the volume knob to adjust the level (
[0]
to
[9]
), then press the knob.
[DIMMER]
Dims the illumination.
[ON]
: Dimmer is turned on.
[OFF]
: Dimmer is turned off.
[DIMMER TIME]
: Set the time to turn on dimmer and to turn off dimmer.
1
Turn the volume knob to adjust the
[ON]
time, then press the knob.
2
Turn the volume knob to adjust the
[OFF]
time, then press the knob.
Default:
[ON]
:
[6:00PM]
;
[OFF]
:
[6:00AM]
[BRIGHTNESS]
Sets the brightness for day and night separately.
1
[DAY]
/
[NIGHT]
: Select day or night.
2
Select a zone. (See the illustration on page 26.)
3
[LVL00]
to
[LVL31]
: Set the brightness level.
[TEXT SCROLL]
[ONCE]
: Scrolls the display information once. ;
[AUTO]
: Repeats scrolling at
5-second intervals. ;
[OFF]
: Cancels.
[CLOCK]
[CLOCK DISPLAY] [ON]
: The clock time is shown on the display even when the unit is turned
off. ;
[OFF]
: Cancels.
[DEMO MODE]
[ON]
: Activates the display demonstration automatically if no operation is
done for about 15 seconds. ;
[OFF]
: Deactivates.
Display Settings
Installation/Connection
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
WARNING
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• To prevent short circuit:
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires
that comes into contact with metal parts to protect the wires.
CAUTION
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Mount the unit at an angle of less than 30°.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
KMM-BT332U_K_B5A-3889-00_EN_1st Draft.indd 27
KMM-BT332U_K_B5A-3889-00_EN_1st Draft.indd 27
7/9/2021 10:59:35 AM
7/9/2021 10:59:35 AM
