14
|
KDC-MP5539U/KDC-MP5039U/KDC-MP4039
Menu Glossary
• SWPRE (Switching Preout)
Switches the preout between rear output (“REAR”)
and subwoofer output (“SUB-W”).
• SUPREME
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate (less
than 128Kbps, Sampling frequency is 44.1kHz).
Supplementing is optimized by compression
format (AAC, MP3 or WMA) and processed
according to bit rate.
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
• CD
READ
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CD may be unplayable even when set to “2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
• AUX
When this is set to ON, AUX source can be selected.
ON1: Outputs the sound of external unit connected
to the AUX terminal when switched to AUX
source.
ON2: Activates the attenuator function when
switched to AUX source.
Turn off the attenuator function when
listening to output from external unit. This
prevents the noise when no external unit is
connected to AUX terminal.
OFF: Disables the selection of AUX source.
Set to OFF when not using the AUX terminal.
• ZONE2 (Dual Zone)
Set the destination (front speaker “FRONT” or rear
speaker “REAR”) of the sub source (AUX IN) when
the Dual Zone function is turned on.
• DISPLAY
If this unit is not operated at least 5 seconds with
“OFF” selected, the display turns off. During a setup
mode, the display will not turn off even if 5 seconds
lapse.
For operating KCA-BT100
To control KCA-BT100, operate as follows;
To make setting for <Selecting the Dialing Mode>,
select <Menu System> (page 10). Pressing the [
38
]
button for at least 1 second after selecting the
"DIALING MODE" item allows you to enter the dialing
method selection mode. To exit from dialing method
selection mode, press [M.JOG] button.
To make <Disconnecting a Call>, <Clearing the
Disconnection Massage>, and <Rejecting an
Incoming call>, press [AUTO] button for at least 1
second.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
Displays of KCA-BT100 Instruction
Manual
Actual displays on this unit
“DISCONCT” “HF
DISCONCT”
“CONNECT” “HF
CONNECT”
“PHN-DEL” “DEVICE
DEL”
“P-STATUS” “DVC
STATUS”
“BT-CON Y”
“HF CONNECT Y”
“T-CON N”
“HF CONNECT N”
: Displays the bluetooth connection status.
This indicator turns on when a cell-phone is
connected to this unit.
: Displays the signal strength of cell-phone.
: Displays the battery level of cell-phone.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have
been classified as Class 1. This means that the unit is
utilizing laser beams that are of a weaker class. There
is no danger of hazardous radiation outside the unit.
Appendix
B64-3956-00̲English̲M̲r1.indd 14
B64-3956-00̲English̲M̲r1.indd 14
07.11.9 4:44:32 PM
07.11.9 4:44:32 PM
