16
KDC-BT7539U/BT8041U
/BT8141UY/BT838U
• Press the remote control [
∗
] key and [AUD] key to enter
the audio adjustment mode.
• Both AUDIO FUNCTION MODE and SETUP MODE ad-
justment items are included.
• By pressing [AUD] and [FM] key brie
fl
y, switch the item to
be adjusted in the following order. (Only in forward rota-
tion)
The default item shall be Fader, and then the item
is forwarded in the following order: Balance
→
Bass
Level
→
Middle Level
→
Treble Level
→
HPF Front
→
HPF
Rear
→
LPF Sub Woofer (thereafter arbitrary).
• Continuous forwarding by remote control is prohibited.
• Fader is adjusted by the VOL knob and [
] / [
] keys
in 3 steps: R15
↔
0
↔
F15. (Default value: 0)
• Balance is adjusted by the VOL knob and [
] / [
]
keys in 3 steps: L15
↔
0
↔
R15. (Default value: 0)
• Bass/Middle/Treble Level are adjusted by the VOL knob
and [
] / [
] keys in 3 steps: -8
↔
0
↔
8. (Default value:
0)
• HPF Front / Rear is adjusted by the VOL knob and [
] /
[
] keys in 2 steps: Through
↔
180Hz (or 220Hz). (Default
value: Through)
• LPF Sub Woofer is adjusted by the VOL knob and [
]
/
[
] keys in 2 steps: 60Hz (or 50Hz)
↔
Through. (Default
value: Through)
• Sub Woofer Phase is adjusted by the VOL knob and [
]
/ [
] keys in 2 steps: Reverse
↔
Normal. (Default value:
Normal)
• Volume Offset (other than the internal AUX) is adjusted
by the VOL knob and [
] / [
] keys in 2 steps: -8
↔
0.
(Default value: 0)
• Volume Offset (the internal AUX) is adjusted by the VOL
knob and [
] / [
] keys in 3 steps: -8
↔
0
↔
+8. (Default
value: 0)
• Loudness ON/OFF is adjusted by the VOL knob and [
]
/ [
] keys in 2 steps: OFF
↔
ON. (Default value: OFF)
• Dual Zone ON / OFF is adjusted by the VOL knob and
[
] / [
] keys in 2 steps: OFF
↔
ON. (Default value:
OFF)
• Bass f / Bass Q / Bass EXT / Middle f / Middle Q / Treble
f are not displayed in the audio adjustment menu.
• SYSTEM Q curve selection is not displayed in the audio
adjustment menu.
●
MENU
• Press the [FNC] key briefly to make the multi-function
display and press the [ ] key brie
fl
y to enter the MENU.
• Press the remote control [DNPP/SBF] key and the
[DIRECT] key to enter the MENU.
• Continuous forwarding by remote control is prohibited.
• Only in the Test mode, add [PH-SEL] (Phone Selection)
in the multi-function display of the STANDBY source and
this shall be included in the initial item (and shall be lo-
cated at the top of the item).
• The initial item in TUNER source MENU source during
the Test mode shall be selectable between Seek ON and
OFF. (European model)
• Only in the Test mode, it shall be made possible to show
“ROM Write Mode” and “ROM Read Mode” items in the
STANDBY source MENU to allow the ROM data transfer
process.
●
Bluetooth
• Connect the unit with the Test mode counterpart unit and
follow the below procedure to do the Audio Loop Back
test.
• While in the source is STANDBY, press and hold the [ATT]
key for 1 second to initialize the BT memory information
to the factory setup.
During the initialization, the message “Initialize....” blinks
(at the period of 1Hz) and at the completion of the initial-
ization the message, “BT_MEM_INIT_OK” is displayed.
(In the case of unsuccessful initialization, the message,
“BT_MEM_INIT_NG” is displayed.)
• Factory setup
Pairing information (Flash Memory) cleared
Telephone number preset (E2PROM) cleared
Friendly name “KENWOOD BT CD/R-2P2” written
PIN code “0000” written
•
Audio Loop Back
Audio Loop Back test can be carried out with BT Audio
source in the Test mode.
(Note: After the Audio Loop Back test, “CK5050” is add-
ed to the list of registered units. After the completion of
the test, without fail reset to the factory setup using the
above procedure.)
1. Add [PH-SEL] (Phone Selection) in the multi-function of
the STANDBY source in the test mode, and the [PH-SEL]
shall be included in the initial item.
2. While in the source is STANDBY, press the [FNC] key
brie
fl
y to show the multi-function display and press the
[ ] key brie
fl
y to enter the Phone Selection mode (Coun-
terpart unit selection mode).
TEST MODE
