ENGLISH
31
Data Size:
B6L (182 mm x 128 mm)
Book Size:
B6L (182 mm x 128 mm)
Source name
Display information
/
STANDBY
Source name (*
2
) Clock (back to the beginning)
TUNER
Frequency (*
2
) Clock (back to the beginning)
(For FM Radio Broadcast Data System stations/FM Radio Data
System stations only)
Station name (*
2
) Radio text Radio text+ Title/Artist Frequency
Clock (back to the beginning)
CD or USB
(For CD-DA)
Disc name/Artist (*
2
) Track title/Artist Playing time Clock
(back to the beginning)
(For MP3/WMA/AAC/WAV/FLAC files)
Track title/Artist (*
2
) Album title/artist Folder name File name
Playing time Clock (back to the beginning)
iPod USB/
iPod BT or
ANDROID
When
[MODE OFF]
/
[BROWSE MODE]
is selected
( 9)
:
Track title/Artist (*
2
) Album title/Artist Playing time Clock
(back to the beginning)
PANDORA/
PANDORA BT
Station name (*
2
) Shared/Radio station Track title Artist
Album title Playing time Clock (back to the beginning)
IHEARTRADIO
Station name (*
2
) Track title/Artist Clock (back to the beginning)
BT AUDIO
Track title/Artist (*
2
) Album title/Artist Playing time
Clock
(back to the beginning)
AUX
Source name (*
2
) Clock (back to the beginning)
*
1
Battery and signal strength of the Bluetooth device will be shown if
[BATT/SIGNAL]
is set
to
[AUTO]
.
( 17)
*
2
Only for
: Turn off the display information.
REFERENCES
INSTALLATION/CONNECTION
Warning
•
The unit can only be used with a 12 V DC power supply, negative ground.
•
Disconnect the battery’s negative terminal before wiring and mounting.
•
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
•
Insulate unconnected wires with vinyl tape to prevent a short circuit.
•
Be sure to ground this unit to the car’s chassis again after installation.
Caution
•
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
•
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
•
Do not connect the
[
wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
•
Mount the unit at an angle of less than 30º.
•
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
•
Keep all cables away from heat dissipate metal parts.
•
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect the
[
terminal of the car
battery.
2
Connect the wires properly.
See Wiring connection.
( 33, 34)
3
Install the unit to your car.
See Installing the unit (in-dash mounting).
( 32)
4
Connect the
[
terminal of the car battery.
5
Press
to turn on the power.
6
Detach the faceplate and reset the unit. ( 3)
JS_KWD_KDC_X301_KN_EN_6.indd 31
JS_KWD_KDC_X301_KN_EN_6.indd 31
23/8/2016 11:22:50 AM
23/8/2016 11:22:50 AM
