14
|
KDC-MP439/KDC-MP3039/KDC-MP339/KDC-MP239/KDC-139
Appendix
About Audio file
• Playable
Model
KDC-MP439, KDC-MP3039, KDC-MP339, KDC-MP239
• Playable Audio file
MP3 (.mp3), WMA (.wma)
• Playable disc media
CD-R/RW/ROM
• Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
• Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from
①
to
⑩
.
CD
v
(
)
<
: Folder
v
: Audio fi
v
v
v
v.
v
Folder
Audio file
An online manual about audio files is put on the
site,
www.kenwood.com/audiofile/
. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
For operating KCA-BT100
To control KCA-BT100, operate as follows;
To make setting for <Selecting the Dialing Mode>,
select <Menu System> (page 10). Pressing the
[
38
] button for at least 1 second after selecting
the "D.MODE" item allows you to enter the dialing
method selection mode. To exit from dialing method
selection mode, press [B.BOOST] button.
To make <Disconnecting a Call>, <Clearing the
Disconnection Massage>, and <Rejecting an
Incoming call>, press [AUTO] button for at least 1
second.
Menu Glossary
• SWPRE
(Switching
Preout)
Switches the preout between rear output (“R”/
“REAR”) and subwoofer output (“SW”/ “SUB”).
• SPRM
(Supreme)
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate.
Supplementing is optimized by compression
format (MP3 or WMA) and processed according to
bit rate.
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
• CD
READ
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CD may be unplayable even when set to “2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
• AUX
When this is set to ON, AUX source can be selected.
ON1: Outputs the sound of external unit connected
to the AUX terminal when switched to AUX
source.
ON2: Activates the attenuator function when
switched to AUX source.
Turn off the attenuator function when
listening to output from external unit. This
prevents the noise when no external unit is
connected to AUX terminal.
OFF: Disables the selection of AUX source.
Set to OFF when not using the AUX terminal.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have
been classified as Class 1. This means that the unit is
utilizing laser beams that are of a weaker class. There
is no danger of hazardous radiation outside the unit.
B64-3901-00̲00̲M̲En.indd 14
B64-3901-00̲00̲M̲En.indd 14
07.7.10 7:18:47 PM
07.7.10 7:18:47 PM
