Kenwood KCA-HX5M Instruction Manual Download

Page: 89 / 97

MENU

Motorcycle Bluetooth Communication System | 89

KCA-HX5M EN

13. GENERAL SETTINGS

13.1 Function Priority

The headset prioritizes connected devices in the
following order:

(highest)

Ambient Mode
Mobile phone
Voice command mode
Mesh Intercom / Bluetooth Intercom
Music sharing via Bluetooth stereo
FM radio
Stereo music by audio cable

(lowest)

Bluetooth stereo music

A lower-priority function gets interrupted by a higher-
priority function. For example, stereo music will
be interrupted by an

Intercom Conversation

; an

Intercom Conversation

will be interrupted by an

incoming mobile phone call.

13.2 Firmware Upgrades

The headset supports firmware upgrades. You can
upgrade the firmware using the

Intercom Device

Manager for KENWOOD

Please visit www.kenwood.com/cs/ce/ to check for the
latest software downloads.

Click Here to Visit

www.kenwood.com/cs/ce/

13. GENERAL SETTINGS

Summary of Contents for KCA-HX5M


































































































Search results

Summary of Contents for KCA-HX5M

Reviews:

Related manuals for KCA-HX5M

Brands by name

Popular brands

Kenwood KCA-HX5M, Instruction Manual

Search results

Summary of Contents for KCA-HX5M

Reviews:

Related manuals for KCA-HX5M

Brands by name

Popular brands