Kenwood Instruction manual Instruction Manual Download Page 43

Page: 43 / 66

Press the

MENU

key to exit the selection.

Press the

PTT

MON

, or

CAL

key to exit Setting Mode.

Note:

Transceiver's individual ID number is not available for

selection as PTT ID.

■

ptt id S

ide

one

When the

PTT

switch is pressed and/or released, a tone

will sound through your own speaker when the PTT ID is

transmitted.

To turn the PTT ID Side Tone on or off:

With the transceiver power OFF, press and hold the

MENU

key while turning the transceiver power ON (for

1 second).

Press the

or key to select “ ”.

Press the

MENU

key then press

or to select

“

” (PTT ID Side Tone is on) or “

” (PTT ID

Side Tone is off).

Press the

MENU

key to exit the selection.

Press the

PTT

MON

, or

CAL

key to exit Setting Mode.

Summary of Contents for Instruction manual



































































Search results

Summary of Contents for Instruction manual

Reviews:

Related manuals for Instruction manual

Brands by name

Popular brands

Kenwood Instruction manual, Instruction Manual

Search results

Summary of Contents for Instruction manual

Reviews:

Related manuals for Instruction manual

Brands by name

Popular brands