Kenwood CT Series Instruction Manual Download Page 26

Page: 26 / 29

CT-2 0 5 0 / 2 0 3 / KXF-W 6 0 1 0 / W 4 0 1 0 (En/ M )

In case of difficulty

Use a cassette w ith unbroken tab or close the
hole.

Close the cassette holder completely.

Adjust the recording level referring to

"How

to record".

Press the input selector key of the source

to be recorded.

Change the tape transport direction of deck
or insert the tape inversely.

Demagnetize the head referring to

"Clean-

ing the head section".

Install the system apart from other electrical
appliances and TV set.

Change the arrangement or the position of the
equipment.

Adjust the recording level referring to

"How

to record".

Set the

DOLBY NR key to B or C.

Clean the capstans and pinch rollers.

Wind the tape regularly by fast forw arding,
rew inding or playing it fully from one reel to
another.

Set the

TIM ER sw itch to OFF unless timer

playback or timer recording is required.

The protection tab on the cassette has been
broken.

The cassette holder is not closed completely.

The recording level is set to the minimum
position.

The TAPE input selector is selected on the
amplifier.

Tape has been fully w ound to a reel.

The head is magnetized.

External noise is induced.

The system assembly position is w rong.

The recording level w as too low .

A tape recorded w ith Dolby NR ON is being
played w ith Dolby NR OFF.

The capstans or pinch rollers are dirty.

Tape is irregularly w ound.

The

TIM ER sw itch is set to PLAY or REC.

Symptom

Remedy

Cause

Recording is not initiated w hen the REC/
ARM (

) key is pressed.

Noise level is high.

Sound is vibrating.

Playback or recording starts immediately
w hen the pow er is sw itched ON.

With some tapes, a squeaky noise is produced w hen the tape is stopped automatically. This is due to the tape protection function, and not
a malfunction.

Note

Downloaded from:

http://www.usersmanualguide.com/

Summary of Contents for CT Series






























Search results

Summary of Contents for CT Series

Reviews:

Brands by name

Popular brands

Kenwood CT Series, Instruction Manual

Search results

Summary of Contents for CT Series

Reviews:

Brands by name

Popular brands