19
Preparations
6
Use the MULTI CONTROL knob or keys to select the appropriate
center speaker setting.
If you selected “LRG” as the front speakers setting,
1
CNTR LRG
(large)
:
A large center speaker is connected to
the receiver.
2
CNTR NML
(normal)
:
An average size center speaker is con-
nected to the receiver.
3
CNTR OFF:
Center speaker setting mode to the
receiver is OFF.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1
Use the MULTI CONTROL knob or keys to adjust the volume
level of the test tone output from the speaker channel to be
adjusted.
The test tone is heard from the speakers in the following
sequence for 2 seconds each:
• If you change the volume level settings for the speakers while listening
to music, the settings referred to on this page are also changed.
•
• If the speaker setting selects are OFF, the speaker level settings are
reset.
2
Press the SET UP key.
• The test tone is turned off. The receiver enters the mode for inputting
the distance to the speakers.
Preparing for surround sound
Speaker settings
If you have selected other than “LRG” as the center speaker
setting,
1
SURR ON:
Surround speaker setting mode to the receiver
is ON.
2
SURR OFF:
Surround speaker setting mode to the receiver
is OFF.
9
Press the SET UP key again to accept the setting.
Turn on the power to this receiver by pressing
POWER (
) key.
Select a speaker system.
1
2
3
1
Press the SET UP key such that the subwoofer setting
indication “SUBW ON” appears.
2
Use the MULTI CONTROL knob or keys to select the appro-
priate subwoofer setting.
1
SUBW ON:
Subwoofer setting mode to the receiver is ON.
2
SUBW OFF:
Subwoofer setting mode to the receiver is OFF.
• The initial setting is “SUBW ON”.
• When the setting “SUBW OFF” is selected, the front speakers are
automatically set to “FRNT LRG” and the procedure skips to step
5
.
• When subwoofer output sound is required, select “FRNT NML”.
3
Press the SET UP key to accept the setting.
• The front speakers setting indication “FRNT” appears.
4
Use the MULTI CONTROL knob or keys to select the appropri-
ate front speakers setting.
1
FRNT NML
(normal)
:
Average size front speakers are
connected to the receiver.
2
FRNT LRG
(large)
:
Large front speakers are con-
nected to the receiver.
• For “FRNT LRG” selection, no sound will be heard from SUBW
even when it is set to ON. However, if you select CINEMA EQ when
subwoofer is selected, you will be able to hear sound from the
subwoofer.
When in STEREO mode, the sound goes directly to front speaker.
5
Press the SET UP key to accept the setting.
• The center speaker setting indication “CNTR” appears.
Adjust the speaker volume level.
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
Continued to next page
If you have selected “NML” as the front speakers setting,
1
CNTR ON:
Center speaker setting mode to the receiver is
ON.
2
CNTR OFF:
Center speaker setting mode to the receiver is
OFF.
7
Press the SET UP key again to accept the setting.
• The surround speaker setting indication “SURR” appears.
8
Use the MULTI CONTROL knob or keys to select the appropriate
surround speaker setting.
If you selected “LRG” as the center speaker setting,
1
SURR LRG
(large)
:
Large surround speakers are con-
nected to the receiver.
2
SURR NML
(normal)
:
Average size surround speakers are
connected to the receiver.
3
SURR OFF:
Surround speaker setting mode to the
receiver is OFF.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RS
LS
TI.VOL
B
CLIP
MUTE
RDS
EON
PTY
TP
TA
NEWS
SW
R
L
SP
A
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RS
LS
TI.VOL
B
CLIP
MUTE
RDS
EON
PTY
TP
TA
NEWS
SW
R
L
SP
A
STEREO
• The receiver enters the speaker volume level adjustment mode.
• In steps
3
and
4
, indications appear only for the selected channels
of the speakers that require adjusting.
The channel indication blinks while the test tone is being output.
STEREO
R
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RS
LS
TI.VOL
B
CLIP
MUTE
RDS
EON
PTY
TP
TA
NEWS
L
SP
A
MULTI CONTROL
(KRF-V7050)
SET UP
POWER
ON/STANDBY
RC-R0720
SET UP
RC-R0613
MULTI
CONTROL
*5027/10-19/EN
3/15/01, 3:09 PM
19
