TK-3202/3206
24
ADJUSTMENT
Test Equipment Required for Alignment
Test Equipment
Major Specifications
1.
Standard Signal Generator
Frequency Range
450 to 490MHz (TK-3202(K, M) TK-3206(M) ) 470 to 512MHz (TK-3202(K2, M2) )
400 to 430MHz (TK-3206(M3) )
(SSG)
Modulation
Frequency modulation and external modulation.
Output
-127dBm/0.1µV to greater than -47dBm/1mV
2.
Power Meter
Input Impedance
50
Ω
.
Operation Frequency
450 to 490MHz (TK-3202(K, M) TK-3206(M) ) 470 to 512MHz (TK-3202(K2, M2) )
400 to 430MHz (TK-3206(M3) )
Measurement Range
Vicinity of 10W
3.
Deviation Meter
Frequency Range
450 to 490MHz (TK-3202(K, M) TK-3206(M) ) 470 to 512MHz (TK-3202(K2, M2) )
400 to 430MHz (TK-3206(M3) )
4.
Digital Volt Meter
Measuring Range
10mV to 10V DC
(DVM)
Input Impedance
High input impedance for minimum circuit loading.
5.
Oscilloscope
DC through 30MHz.
6.
High Sensitivity
Frequency Range
10Hz to 1000MHz.
Frequency Counter
Frequency Stability
0.2ppm or less.
7.
Ammeter
5A.
8.
AF Volt Meter
Frequency Range
50Hz to 10kHz.
(AF VTVM)
Voltage Range
1mV to 10V.
9.
Audio Generator (AG)
Frequency Range
50Hz to 5kHz or more.
Output
0 to 1V.
10.
Distortion Meter
Capability
3% or less at 1kHz.
Input Level
50mV to 10Vrms.
11.
Spectrum Analyzer
Measuring Range
DC to 1GHz or more
12.
Tracking Generator
Center frequency
50kHz to 600MHz
Output Voltage
100mV or more
13.
8
Ω
Dummy Load
Approx. 8
Ω
, 3W.
14.
Regulated Power Supply
5V to 10V, approx. 3A
Useful if ammeter equipped.
■
The following parts are required for
adjustment
1. Antenna connector adapter
The antenna connector of this radio uses an SMA terminal.
Use an antenna connector adapter [SMA(f) – BNC(f) or
SMA(f) – N(f)] for adjustment. (The adapter is not provided as
an option, so buy a commercially-available one.)
2. Repair Jig (Chassis)
Use jig (part No.: A10-4086-03) for repairing the TK-3202/
3206. Place the TX-RX unit on the jig and fit it with screws.
The jig facilitates the voltage check and protects the final
amplifier FET when the voltage on the flow side of the TX-RX
unit is checked during repairs.
3. Battery Jig (W05-1011-00)
+ Terminal (Red)
– Terminal (Black)
Connect the power cable properly between the battery jig
installed in the transceiver and the power supply, and be sure
output voltage and the power supply polarity prior to switching
the power supply ON, otherwise over voltage and reverse
connection may damage the transceiver, or the power supply
or both.
Note:
When using the battery jig, you must measure the
voltage at the terminals of the battery jig. Otherwise, a slight
voltage drop may occur within the power cable, between the
power supply and the battery jig, especially while the
transceiver transmits.
+ Terminal
(Red)
– Terminal
(Black)
C3
100
m
/25V
C2
470P/25V
C1
100P/25V
R1
1.8M
–
S
+
Power
supply
Power cable
SCHEMATIC DIAGRAM
