Kenwood 1032 - KDC Radio / CD Player Instruction Manual Download Page 20

Page: 20 / 22

English

Troubleshooting Guide

What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.

General

The power does not turn ON.

✔

The fuse has blown.

☞

After checking for short circuits in the wires,

replace the fuse with one with the same
rating.

There’s a source you can’t switch.

✔

There’s no media inserted.

☞

Set the media you want to listen to. If there’s

no media in this unit, you can’t switch to each
source.

The memory is erased when the ignition is

turned OFF.

✔

The ignition and battery wire are incorrectly

connected.

☞

Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

Even if Loudness is turned ON, high-pitched tone

isn’t compensated for.

✔

Tuner source is selected.

☞

High-pitched tone isn’t compensated for when

in Tuner source.

No sound can be heard, or the volume is low.

✔

The fader or balance settings are set all the way to

one side.

☞

Center the fader and balance settings.

✔

The input/output wires or wiring harness are

connected incorrectly.

☞

Reconnect the input/output wires or the

wiring harness correctly. See the section on
<Connecting Wires to Terminals>.

✔

The values of Volume offset are low.

☞

Turn up the Volume offset, referring to the

section on <Audio Control> (page 8).

The sound quality is poor or distorted.

✔

One of the speaker wires is being pinched by a

screw in the car.

☞

Check the speaker wiring.

✔

The speakers are not wired correctly.

☞

Reconnect the speaker wires so that each

output terminal is connected to a different
speaker.

The Touch Sensor Tone doesn’t sound.

✔

The preout jack is being used.

☞

The Touch Sensor Tone can’t be output from

the preout jack.

Tuner source

Radio reception is poor.

✔

The car antenna is not extended.

☞

Pull the antenna out all the way.

✔

The antenna control wire is not connected.

☞

Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

B64-3239-00̲K̲English.Indd 20

05.7.29 0:46:08 PM

Summary of Contents for 1032 - KDC Radio / CD Player























Search results

Summary of Contents for 1032 - KDC Radio / CD Player

Reviews:

Related manuals for 1032 - KDC Radio / CD Player

Brands by name

Popular brands

Kenwood 1032 - KDC Radio / CD Player, Instruction Manual

Search results

Summary of Contents for 1032 - KDC Radio / CD Player

Reviews:

Related manuals for 1032 - KDC Radio / CD Player

Brands by name

Popular brands