To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com
INSTRUCTIONS FOR USE
Blue 32
– 146 2301 000(1)2005-03
7
Stopping the machine
To stop the machine, release the drive lever (4, Fig. C)
completely and pull back on handle bar.
To stop the brooms from rotating, turn the key (2, Fig. B)
to “0” position.
To lift the side broom (10, Fig. C), lift the knob (12, Fig. C)
(without turning it) and align the latch with the slot in the
plastic chassis. Rotate the knob (12) forward to engage
the latch (2).
MACHINE OPERATION
1.
Avoid stopping for a long time with the machine in the
same position and the brooms still rotating: this could
create unwanted marks on the floor.
2.
To pick-up large debris, could be lifted the front skirt
by pulling the option lever; keep in mind that during
this operation the dust control of the machine will
decrease.
3.
For proper machine operation, the dust filter must be
as clean as possible. To clean the filter while
sweeping proceeds as follows according to the type
of filter-shaker installed:
a)
Manual filter - shaker
: turn the ignition key in
the “0” position, then pull the handle (20, Fig. C)
outward until the end of the stroke is reached
and then release it: the return spring strikes the
dust filter frame and shakes it.
Repeat this operation several times. Turn the
ignition key in the “I” position to continue
working.
b) Electric
filter-shaker
(optional) press and hold
the filter-shaker button (8, Fig. B) for a few
seconds.
.
The hopper (17, Fig. C) should be emptied after each
working period and whenever it is full.
EMPTYING THE HOPPER
1.
Release the drive lever to stop the machine.
2.
Turn the ignition key (2, Fig. B) to the “0” position.
3.
Disengage the hopper latch (18, Fig. C) by pulling
the bottom outward.
4.
Using the hopper handle (19, Fig. C) remove the
hopper (17, Fig. C) from the machine and empty it.
5.
Return the hopper to its normal operating position
and engage the hopper latch (18, Fig. C).
6.
The machine is ready to start sweeping again.
AFTER MACHINE USE
When finished working:
1.
Clean the filter using the manual filter shaker (20,
Fig. C) or the electric filter-shaker, if equipped, by
pressing the filter shaker button (8, Fig. B).
2.
Empty the hopper (17, Fig. C) (see previous
paragraph).
3.
Lift the side broom by lifting the knob (12, Fig. C).
4.
Remove the ignition key (2, Fig. B) from the machine.
5.
Ensure that the machine cannot move
independently.
6.
Activate the optional brake pedal (26, Fig. C).
PUSHING THE MACHINE
The machine can be moved my pushing it both with the
ignition key (2, Fig. B) in the “0” and in the “I” positions.
MACHINE STORAGE
If you foresee that the machine will not be used for more
than 30 days, proceed as follows:
–
Move the machine to a suitable indoor storage area.
–
Disconnect the battery connector (3, Fig. U).
–
Lift the machine so that the skirts, the main broom
and the wheels do not touch the ground.
–
Disconnect the positive battery terminal (+) from the
positive battery (+) pole.
NOTE:
Repeat the operation at least every ten
minutes while working (according to the
dust conditions)
NOTE:
During this operation the electric motors
and all machine functions are automatically
stopped.
NOTE:
When the hopper and/or filter are full the
machine can not collect more dust and
debris.
CAUTION!
To avoid damaging the dust filter do not
sweep wet floors or ground.
