Kenmore Viking 970, Use And Care Manual

Page: 17 / 44

17
ENGLISH
Setting Warmer Drawer Controls
(cont’d)
Fig. 1
Fig. 2
To Remove Warmer Drawer:
1. Turn power OFF before removing the warmer drawer.
2. Open the drawer to the fully opened position.
3. On the right glide you will find a shield attached with a hex-head
screw (see figure 1). Using a 1/4” socket and ratchet remove the
shield.
4. Locate glide lever on each side of drawer, pull up on the left glide
lever and push down on the right glide lever.
5. Pull the drawer away from the range.
To Replace Warmer Drawer:
1. Replace shield on the right glide of the drawer body.
2. Pull the bearing glides to the front of the chassis glide (see
figure 2).
3. Align the glide on each side of the drawer with the glide slots on the
range.
4. Push the drawer into the range until levers “click” (approximately
2”). Pull the drawer open again to seat bearing glides into position.
If you do not hear the levers “click” or the bearing glides do
not feel seated remove the drawer and repeat steps 2-4.
This
will minimize possible damage to the bearing glides.
Self-Cleaning
During the Self-Cleaning cycle, the outside of
the range can become very hot to the touch. DO NOT leave
small children unattended near the appliance.
The health of some birds is extremely
sensitive to the fumes given off during the Self-Cleaning
cycle of any range. Move birds to another well-ventilated
room.
DO NOT line the oven walls, racks, OVEN
BOTTOM or any part of the range with aluminum foil .
Doing so will destroy heat distribution, produce poor baking
results & cause permanent damage to the oven interior
(aluminum foil will melt to the interior surface of the oven).
DO NOT force the oven door open. This can
damage the automatic door locking system. Use caution
when opening the door after the Self-Cleaning cycle is
completed. The oven may still be VERY HOT.
Self-Cleaning Oven
A Self-Cleaning oven cleans itself with high temperatures
(well above cooking temperatures) which eliminate soils
completely or reduces them to a fine powdered ash you can
wipe away with a damp cloth.
Prepare for the Self-Cleaning Cycle with the following
precautions:
•
DO NOT use oven cleaners or oven protective coatings
in or around any part of the Self-Cleaning oven.
• DO NOT clean the oven door gasket. The woven
material of the oven door gasket is essential for a good
seal. Care should be taken not to rub, damage or
remove the gasket.
• DO NOT use any cleaning materials on the oven door
gasket. Doing so could cause damage.
• Remove the broiler pan & insert, all utensils & ANY
aluminum foil. These items cannot withstand high
cleaning temperatures.
• Remove the oven racks. If the racks are left in the oven
during the Self-Clean cycle their color will turn slightly
blue & the finish will be dull. After the cycle is complete
and the oven has cooled, rub the sides of the oven
racks with wax paper or a cloth containing a small
amount of salad oil (this will make the oven racks glide
easier into the oven rack positions).
• Remove any excessive spillovers in the oven cavity
before starting the Self-Cleaning cycle. To clean, use
hot, soapy water and a cloth. Large spillovers can
cause heavy smoke or fire when subjected to high
temperatures.
DO NOT allow food spills with a high
sugar or acid content (such as milk, tomatoes,
sauerkraut, fruit juices or pie filling) to remain on the
surface as they may leave a dull spot even after
cleaning.
• Clean any soil from the oven frame, the door liner
outside the oven door gasket and the small area at the
front center of the oven bottom. These areas heat
sufficiently to burn soil on. Clean with soap and water.
• NOTE: Prior to setting the Self-Clean cycle, any spills
remaining on the oven bottom should be removed.