manualshive.com logo in svg

Kenmore SPACEMASTER 85210, Installation Instructions Manual

Share
Download
Kenmore SPACEMASTER 85210 Installation Instructions Manual Download Page 14

- 14 -

1. Remove the upper cabinet and wall templates.

NOTE: If you are venting the oven through the wall,

be sure you align the damper/connector on
the rear of the mounting plate with the 
3 1/4"x10" duct. Be sure the damper moves
freely. See Figure 22.

2. Place the mounting plate against the wall and match

the screw holes.

3. Prepare the toggle bolts by attaching a spring toggle

head to the end of each toggle bolt as shown in
Figure 23.

NOTE: Be sure to leave at least one wall-thickness of

space between the head of the toggle bolt
and the spring toggle head so that the spring
toggle can open on the other side of the wall,
as shown in Figure 24.

4. Locate the stud holes (3/16") and insert the lag

screws through the mounting plate and into the holes.
See Figure 25.

5. Insert the toggle bolts through the dry wall holes

(3/4"). Tighten the toggle bolts.

6. Slide washer onto lock pin and place inside upper

cabinet for future use as directed on the next page.
See Figure 26.

STEP 5: 
INSTALL THE MOUNTING PLATE

wall mounting plate

toggle bolt

lag screw

mounting pate

lock pin

washer

wall

mounting plate

toggle bolt

spring
toggle head

mounting plate

spring

toggle head

Figure 22

Figure 23

Figure 24

Figure 25

Figure 26

Summary of Contents for SPACEMASTER 85210

















Reviews:

No comments

Brands by name

Popular brands

Load more brands