Kenmore D02 M90230, Use & Care Manual

Page: 12 / 28

CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Turn controls and gas source when not in use.
WARNING
NOTE: Your grill may NOT be equipped with a Side
burner!
Side burner Ignitor Lighting
1. Turn OFF gas burner control valves.
2. Turn ON gas at LP cylinder.
3. To ignite SIDE BURNER, open side burner cover.
4. Turn side burner knob to the HIGH position. Push IGNITOR
button rapidly.
5. If side burner does not light in 5 seconds, turn knob to
OFF , wait 5 minutes, then repeat lighting procedure.
Side burner Match Lighting
1. Turn ON gas at LP cylinder.
2. Hold lit match to any port on
the burner. Push in and turn side
burner knob to the
HIGH
position. Be sure the burner
lights and stays lit.
12 • 466724112
Match-Lighting
s
Do not lean over grill while lighting.
1. Turn OFF gas burner control valves.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. Place match into match holder (hanging from side of
cart). Strike the match.
5. Place lit match through the match light hole and near the
burner. Push in and turn left knob to the HIGH position.
Be sure the burner lights and stays lit.
6. Light adjacent burners in sequence by pushing knobs in
and turning to the HIGH position.
Burner Flame Check
• Remove cooking grates and heat diffusers. Light burners,
rotate knobs from HIGH to LOW . You should see a
smaller flame in LOW position than seen on HIGH .
Perform burner flame check on side burner, also. Always
check flame prior to each use. If only low flame is seen
refer to "Sudden drop or low flame" in the
Troubleshooting Section.
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop or turn of NG
source.
Ignitor Check
• Turn gas off at LP cylinder or source.
Press and hold
electronic ignitor button. "Click" should be heard and
spark seen each time between each collector box or
burner and electrode. See "Troubleshooting" if no click or
spark.
Valve Check
• Important: Make sure gas is off at LP cylinder or source
before checking valves . Knobs lock in OFF position. To
check valves, first push in knobs and release, knobs
should spring back. If knobs do not spring back, replace
valve assembly before using grill. Turn knobs to
LOW
position then turn back to OFF position. Valves should
turn smoothly.
Hose Check
•
Before each use, check to see if hoses are cut or worn or
kinked. Replace damaged hoses before using grill. Use
only valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease
and smoke for paint. Interiors of gas grills are not
painted at the factory
(and should never be painted) .
Apply a strong solution of detergent and water or use a
grill cleaner with scrub brush on insides of grill lid and
bottom. Rinse and allow to completely air dry.
Do not
apply a caustic grill/oven cleaner to painted surfaces.
• Plastic parts: Wash with warm soapy water and wipe
dry. Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to
and failure of parts can result.
• Porcelain surfaces: Because of glass-like composition,
most residue can be wiped away with baking
soda/water solution or specially formulated cleaner.
Use
nonabrasive scouring powder for stubborn stains.
• Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water. Wipe dry
with a soft nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill’s high
quality appearance, wash with mild detergent and warm
soapy water and wipe dry with a soft cloth after each
use. Baked-on grease deposits may require the use of an
abrasive plastic cleaning pad. Use only in direction of
brushed finish to avoid damage. Do not use abrasive pad
on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any
of the grill cooking surfaces, ensure no loose bristles
remain on cooking surfaces prior to grilling. It is not
recommended to clean cooking surfaces while grill is hot.
HIGH
LOW