manualshive.com logo in svg

Kenmore 721.62642, Basic Field Manual

Share
Download
Kenmore 721.62642 Basic Field Manual Download Page 16

IMPORTANT NOTES:

UNIT MUST BE DISCONNECTED FROM ELEC-
TRICAL OUTLET WHEN MAKING REPAIRS, RE-
PLACEMENTS, ADJUSTMENTS AND CONTIN-
UITY CHECKS. WAIT AT LEAST ONE MINUTE,
UNTIL THE HIGH VOLTAGE CAPACITOR IN THE
HIGH VOLTAGE POWER SUPPLY HAS FULLY
DISCHARGED.
THE CAPACITOR SHOULD BE DISCHARGED BY
USING INSULATED WIRE - I.E. TEST PROBE
CONNECTED TO 10K-OHM RESISTOR IN SERIES
TO GROUND.
WHEN RECONNECTING THE WIRE LEADS TO
ANY PART, MAKE SURE THE WIRING CONNE-
CTIONS AND LEAD COLORS ARE CORRECTLY
MATCHED ACCORDING TO THE OVERALL CIR-
CUIT DIAGRAM. (ESPECIALLY SWITCHES AND
HIGH VOLTAGE CIRCUIT.)

A. REMOVING POWER AND CONTROL

CIRCUIT BOARD (Figures 1, 2 and 3)

(1) Remove a screw securing the control panel

assembly to the oven cavity.

(2) Remove the control panel with pushing it upward.
(3) Remove the connectors (CN1) and wire leads

(Relay2) from the circuit board.

(4) Remove 3 screws securing the circuit board.

(5) Remove the FPC connector from the terminal

socket following “HOW TO REMOVE THE FPC
CONNECTOR” on the next page.

(6) Remove the circuit board from the control bracket

carefully.

7-4

DISASSEMBLY INSTRUCTIONS

Figure 1

 Control Panel

(Relay 2)

(CN1)

Power Transformer

Relay 2

 Circuit Board

Figure 2

Figure 3

Control Bracket

 Circuit Board

FPC Connector(S1)

Summary of Contents for 721.62642














































Reviews:

No comments

Brands by name

Popular brands

Load more brands