Turning Grill Off
• Turn all knobs to
OFF
position. Turn LP tank off by turning
OPD hand wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP tank.
Push and turn burner control to .
"Clicking" should be heard and sparking seen each time
between collector box or burner and electrodes. See
"Troubleshooting"
if no click or spark occurs.
Valve Check
• Important: Make sure gas is off at LP tank before checking
valves
. Knobs lock in
OFF
position. To check valves, first
push in knobs and release, knobs should spring back. If knobs
do not spring back, replace valve assembly before using grill.
Turn knobs to
LO
position then turn back to
OFF
position.
Valves should turn smoothly.
General Grill Cleaning
• Keep the outside of your grill looking new by cleaning it once a
month with warm soap and water or a non-abrasive cleaner. If
you don’t have a grill cover, wipe off dust and grime before
starting your grill.
• Coating the cooking grids with spray-on cooking oil will keep the
food from sticking and make clean up easier. After cooking,
scrape the grates with a long handled, brass wire bristle brush.
• Check inside the grill bottom for grease build up and clean
often, especially after cooking fatty meat.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Apply a strong solution of detergent and water
or use a grill cleaner with scrub brush on insides of grill lid and
bottom. Rinse and allow to completely air dry.
Do not apply a
caustic grill/oven cleaner to painted surfaces.
464222009 • 9
CAUTION
SPIDER ALERT!
VALVE
CONTROL PANEL
SPIDER WEBS
INSIDE TUBE
If you notice that your grill is getting hard to light or that the
flame isn’t as strong as it should be, take the time to check and
clean the burners.
In some areas of the country, spiders or small insects have been
known to create “flashback” problems. The spiders spin webs, build
nests and lay eggs in the grill’s burner tube(s) obstructing the flow of
gas to the burner. The backed-up gas can ignite in the tube behind
the control panel. This is known as a flashback and it can damage
your grill and even cause injury.
To prevent flashbacks and ensure good performance the burner
assembly should be removed from the grill and cleaned before use
whenever the grill has been idle for an extended period.
BURNER
SPIDER AND WEBS
INSIDE BURNER TUBE
• Plated wire grates:
Wash grates with concentrated grill
cleaner or use soap and water solution. Dry thoroughly and
store indoors between cookouts.
•
Plastic parts:
Wash with warm soapy water and wipe dry.
s
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain grates:
Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner.
Use non-abrasive scouring
powder for stubborn stains.
• Cooking surfaces:
If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
Before Your First Cookout
• Light burners, check to make sure they are lit, close the lid and
warm up grill on HIGH for 15 minutes. This curing of paint and
parts will produce an odor only on first lighting.
Burner Flame Check
• Light burner, rotate knobs from HIGH to LOW. You should see
a smaller flame in
LOW position than seen on HIGH. Always
check flame prior to each use. If only low flame is seen refer to
"Sudden drop or low flame" in the
Troubleshooting Section
.
HI
LO
Hose Check
•
Before each use, check to see if hoses are cut, worn or kinked.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified in the Parts List.
Normal
Hose
Kinked
Hose
Summary of Contents for 415.16644900
Page 30: ...NOTES 30 464222009 ...
Page 31: ...NOTES 464222009 31 ...
