5
PARTS INCLUDED WITH HOOD
TOOLS NEEDED FOR HOOD INSTALLATION
Aluminum Grease Filters
(2 per hood)
Parts Bag
(4 no. 8-18 x 1/2" metal screws,
6 no. 8 x 5/8" round head wood screws,
6 no. 8 x 1/2" countersunk wood screws,
1 bulb suction cup tool)
Screwdriver
(Flat & Phillips no. 2)
Pencil
Tape
Measure
Drill
(with 1/8" and
7/64" drill bits,
and 1½" hole saw)
Sabre Saw
Keyhole
Saw
-or-
Metal Foil
Duct Tape
Wire
Stripper
PARTS NOT INCLUDED WITH HOOD
OPTIONAL PARTS (purchase separately)
Shielded Halogen Bulbs
(120 V, 50 W max., MR16 or
PAR16 with GU10 base)
(2 per hood)
Part No. SV05921
Non-Ducted Recirculation Filters
(Non-ducted hoods only)
(2 per hood)
Part No. S97020466
7-inch Round Damper
(For use with 7-inch Round Duct)
Part No. 59183
“Parts Not Included With Hood” available by calling
1-844-553-6667
3¼” x 10”
Damper / Duct Connector
C
L
A
B
Apoyar este borde contra la pared de atrás
Place this edge against back wall
VERTICAL EXHAUST
S
A
A
V
RTICAL EX
= 3¼” x 10”
= 3¼” x 14”
R
ECTANGULAR
D
UCTING
7” R
OUND
D
UCTING
OR
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
= 3¼ po x 10 po
= 3¼ po x 14 po
C
ONDUIT
RECTANGULAIRE
C
ONDUIT
ROND
DE
7
PO
OU
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
C
ONDUCTO
RECTANGULAR
C
ONDUCTO
REDONDO
DE
7
PULG
.
O
Appuyer ce bord au mur arrière
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
M
ARK
WHERE
INDICATED
FOR
THE
APPROPRIATE
SIZE
DUCT
OPENING
M
ARQUER
LES
REPÈRES
AUX
ENDROITS
INDIQUÉS
SELON
LE
FORMAT
DE
CONDUIT
UTILISÉ
T
ITLE
TO
BE TRANSLATED
IN
S
PANISH
Electrical access hole center
A
= single blower hood
B
= double blower hood
Centre du trou pour fil
d’alimentation électrique
A
= hotte ventilateur simple
B
= hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A
= single blower hood
B
= double blower hood
4¼”
10½”
14½”
8”
7½”
C
C
C
Bend template along graduated
scale when installing to framed
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
conséquence.
To be translated in Spanish.
EZ-1 One person Installation Kit
(including template for
ducting, printed both sides,
and installation brackets)
7” Round Duct Connector
Long Nose
Pliers
HR0064
Sheet Metal
Shears
