Kenmore 111 Page 35 Use & Care Manual Download

Page: 35 / 46

WATER FILTER

Installation

✳

Turn off the water supply to the refrigerator. Dispense

water for 3 seconds to prevent water drops from falling

while installing filter.

The water filter is located in

the top of the refrigerator

compartment. Pull the water

filter cover toward you and

down.

Remove the locking cap by turning 1/2

counterclockwise. Save locking cap for possible future

use. Always install locking cap if no filter is in place.

Insert water filter and rotate

clockwise 1/2 turn to secure

in place. Raise the water filter

cover and slide back into place.

Before proceeding, use a cloth

to wipe up any water droplets

that may have fallen.

Dispense water over the course of 5 minutes in cycles

of 30 seconds ON and 60 seconds OFF. Do not

dispense water continuously for 5 minutes.

NOTE :

Perform this step each time a new water filter

is installed.

✳

One filter is supplied with the refrigerator.

A replacement filter can be purchased at a Sears

store or by calling 1-844-553-6667.

Air Filter

NOTE:

Air Filter should be changed every 6 months.

Replacing the water filter at same time as air filter is

recommended.

Information concerning the water fi lter

- After use, the water system is subject to low pressure.

Proceed with caution when removing the filter.

Dispenser water 1-3 seconds before water filter change

to prevent water drops from falling.

Flush the water system if the appliance has not been

in use for a long period of time, or if the ice/water has

an unpleasant taste or smell. To do this, dispense water

through the water dispenser for several minutes.

If the unpleasant taste or smell remains, replace the filter.

To protect from frost, remove the filter cartridge if you

expect the temperature to drop below freezing.

- If pressure surges could occur in the water pipe, do not

install the water filter without a suitable surge eliminator.

Contact an installation expert if you are not sure

whether pressure surges could occur in the water pipe.

- After installing a new filter : Discard any ice produced

in the first 24 hours after switching on.

- If no ice has been removed for a long period of time,

empty the ice cube bin and discard any ice produced

over the next 24 hours.

WARNING

To reduce the risk associated with ingestion of contaminants:

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before and

after the system. Systems certified for cyst reduction may

be used on disinfected water that may contain filterable

cysts. EPA Establishment Number 10350-MN-005

CAUTION

To reduce the risk associated with property damage

due to water leakage:

•

Read and follow

the Water Filter instructions before

installation and use of this system.

• Installation and use

MUST

comply with all state and

local plumbing codes.

•

Do not

install if water pressure exceeds 125 psi

(862 kPa). Contact a plumbing professional if you

are uncertain of how to check your water pressure.

•

Do not

install where water hammer conditions may

occur. If water hammer conditions exist, you must

install a water hammer arrester. Contact a plumbing

professional if you are uncertain of how to check for

this condition.

•

Do not

install on hot water supply lines.

The maximum operating water temperature of this

water filter system is 100°F (38°C).

•

Protect water fi lter from freezing

. Do not operate

refrigerator in ambient conditions below 55°F

(12.7°C). Drain water filter when storing unit in

temperatures below 40°F (4.4°C).

• The disposable water filter must be replaced every

six months, at the rated capacity, or if a noticeable

reduction in flow rate occurs.

Slim Ice Maker

OPEN

ACCELA CHILL

ACCELA CHILL
HOLD 3 SEC

Rotate filter cover

counterclockwise about 15

degrees to release from

underlying duct cover. Pull filter

cover toward you to remove.

Slide used filter up out of back

of filter cover. Slide new filter

down into back of filter cover.

Align filter cover at about

a 15 degree angle to duct

cover. Push filter cover down

onto duct cover and rotate

clockwise to secure.

After changing the water filter

or air filter, be sure to press the

Water Filter or Air Filter button

for 3 seconds turn indicator

light off.

FDR 30Cuft_UCG(영+스)(Kenmore)_F840-1.indd 35

2020-02-26 오전 11:53:57

Summary of Contents for 111















































Search results

Summary of Contents for 111

Reviews:

Related manuals for 111

Brands by name

Popular brands

Kenmore 111, Use & Care Manual

Search results

Summary of Contents for 111

Reviews:

Related manuals for 111

Brands by name

Popular brands