Kendall Howard KH-5000-3-200-72 Assembly And Maintenance Manual Download Page 7 | Manualshive

Page: 7 / 14

background image

Step 6. Attach the Work Surface

Stand the bench in its upright position and place the work surface on top of the bench.
Attach work surface with (4) 1 ½ Hex Drive Bolts on each side. You may now tighten
both the Hex Drive Bolts and the cross head screws on both the work surface and the
lower shelf.

7

«
...
5
6
7
8
9
...
»

Summary of Contents for KH-5000-3-200-72















Reviews:

No comments

Related manuals for KH-5000-3-200-72

Brand: Ratoc Systems Pages: 36

Brand: Navigloo Pages: 3

Brand: Bahco Pages: 4

Brand: M-system Pages: 3

Brand: Palmako Pages: 62

Brand: TerraMaster Pages: 13

Brand: AIC Pages: 105

Brand: Glyph Pages: 7

Brand: NewerTech Pages: 12

Brand: Panasonic Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 50

Brand: Sony Pages: 124

Brand: Sony Pages: 136

Brand: Electron Microscopy Sciences Pages: 3

Brand: Supermicro Pages: 126

Brand: Quantum Pages: 3

mini usb 2.0 companion hard drive

Brand: LaCie Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands