Kemppi Flexlite GX 203G Operating Manual Download Page 5

Page: 5 / 49

Flexlite GX

Operating manual - EN

2. ABOUT EQUIPMENT

The Flexlite GX MIG welding gun equipment consists of:

The exact visual details may be different between different Flexlite GX models.

Gas nozzle

Contact tip

Contact tip adapter / gas diffuser

Gun neck

Handle

Trigger switch

Cover plate

>> This covers the handle if a welding gun remote is not used (Flexlite GX K5 and K8 level models). For more

information on the gun remotes, refer to "Installing gun remote" on page 10.

>> Not available with Flexlite GX K3 level models.

Gun connector

Coolant inlet and outlet hose connectors

>> With water-cooled welding guns only.

10.

Neck tightening collar

>> With multi-neck welding guns only.

6/49

1921390 / 2002

Summary of Contents for Flexlite GX 203G


















































Search results

Summary of Contents for Flexlite GX 203G

Reviews:

Related manuals for Flexlite GX 203G

Brands by name

Popular brands

Kemppi Flexlite GX 203G, Operating Manual

Search results

Summary of Contents for Flexlite GX 203G

Reviews:

Related manuals for Flexlite GX 203G

Brands by name

Popular brands