Kemppi Flexlite GX 203G Operating Manual Download Page 9 | Manualshive

Page: 9 / 49

background image

Flexlite GX

Operating manual - EN

3.2 Installing gun remote

The Flexlite GX K5 level welding gun remote can be used with Kemppi Fastmig equipment only.

The Flexlite GX K8 level welding gun and digital gun remote can be used with Kemppi X8 MIG Welder only.

Ensure that the welding equipment is not connected to the mains or that the welding gun is not connected at this
stage.

Tools needed:

TX20

1.

Remove the cover by releasing the screws on the sides and then moving the cover slightly forward and up.

2.

Remove the existing circuit board chip from the connectors inside the gun.

© Kemppi

10/49

1921390 / 2002

«
...
7
8
9
10
11
...
»

Summary of Contents for Flexlite GX 203G


















































Reviews:

No comments

Related manuals for Flexlite GX 203G

Brand: Fender Pages: 3

Brand: Magnavox Pages: 24

Brand: Magnavox Pages: 22

Brand: Magnavox Pages: 21

Magnavox FW 750C

Brand: Magnavox Pages: 28

Magnavox FW 2012

Brand: Magnavox Pages: 16

Brand: QFX Pages: 2

Brand: Abus Pages: 14

Brand: Panasonic Pages: 4

Brand: Neopost Pages: 119

Brand: cias Pages: 80

Brand: TANDBERG Pages: 12

Brand: X2 Digital Wireless Systems Pages: 16

Brand: DAD Pages: 48

Brand: ADT Pages: 62

Brand: Livoo Pages: 6

Brand: Coby Pages: 3

MAGNUM ALERT 854 SYSTEM

Brand: NAPCO Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands