manualshive.com logo in svg

Kemco 50-0230B-002, Installation Instructions Manual

Share
Download
Kemco 50-0230B-002 Installation Instructions Manual Download Page 6

                                                                                                6

 
 
 
 
13. Measure 7” from rear A/C control opening 

toward the rear of vehicle. Using a razor knife, 
carefully cut an opening in the headliner that is 
6” wide x 8 3/4” long. Make sure that the 6” 
width is centered in the vehicle. 

Caution: Before 

cutting headliner material, check for wiring 
or other componentry above headliner. Cut 
only where indicated.        

See Figure 10.

 

14. Insert the 6” x 14” piece of plywood through 

opening and rotate 90 degrees.  See Figure 10.

 

 

 
 
 

 
 
 

 
 

II. PREPARATION OF CONSOLE FOR INSTALLATION 

 

 
 
 

15. Install front light fixture and secure using  (3) three  

# 6 x 1/2” screws.  Make sure fixture is centered. 
See Figure 11.  

16. Install trim ring around light. 
17. Install rear light fixture and secure using (1) one     

# 6 x 1/2” screw in the center hole only. Make sure 
fixture is centered. Predrill the remaining (2) two 
holes using a 3/32” drill bit. 

18. Install front A/C controls original manner. Secure 

using four (4) # 6 x 3/8” screws.      See Figure 11. 

 
 
 
 
 
 

 
 

III. INSTALLATION OF CONSOLE 

NOTE: Additional assistance in mounting the overhead console in vehicle is advised 

to prevent damage to console or components.

 

 

 

 

FIGURE 10

 

FIGURE 11

 

Summary of Contents for 50-0230B-002









Reviews:

No comments

Brands by name

Popular brands

Load more brands