manualshive.com logo in svg

Kelvinator KCT27036A, Installation Manual, Page: 17 / 32

Share
Download
Kelvinator KCT27036A Installation Manual Download Page 17

Kelvinator solar hot water systems

  installation diagram – electric boosted evacuated tube collectors    17

Installation diagram – electric boosted evacuated tube collectors

Tiled roof

 – preferred method: Connect roof straps from bottom rail and 

top edge of collectors to vertical roof beams. Secure with 2 screws at top 

of beams. Connect roof straps from bottom rail and top of collectors to 

horizontal beams if vertical beams are not accessible.

All numbered items are supplied with the hot water system. Please refer to the Components list for details. Items which are not numbered are not supplied and 

need to be supplied by the installer in accordance with local plumbing requirements. Installation of this hot water system must be completed by an authorised and 

licensed person in accordance with all local regulations, including AS3500 plumbing and drainage requirements and AS3000 electrical wiring standards.

Bottom rail connection viewed 

from above

10-15mm  

from horizontal

bottom rail 

assembly

1.5m

relief valve

uncontrolled  

hot water  

outlet  

(kitchen,  

laundry)

tempered  

(50°C) hot  

water outlet 

(bathrooms)

tempering 

valve

20-30mm  

from horizontal

30-45mm  

from horizontal

Connecting strap viewed from 

roof cavity

Components shown in grey are only used in 2 and 3 collector panel connections

Secure with screws on top  

and back edge of beam

Iron roof:

 Connect bottom 

rail and top edge of 

collectors to iron roof.

Connecting top of 

collectors to tiled 

roof using twisted 

metal straps.

isolating 

and non 

return 

valve

pressure limiting 

valve (600kPa) 

may be required 

if pressure 

exceeds 600kPa

pressure relief 

valve (700kPa) 

may be required 

refer to local 

plumbing 

guidelines

drain

cold 

inlet

flow

Ø20mm  

conduit

relief 

valve

from 

solar

return

horizontal

insert sensor here then 

apply silicone to seal. 

Cable tie the sensor 

wire to outside of the 

pipe insulation, ensuring 

that the wire does not 

touch the hot pipe.

outlet

earth terminal

earth

neutral terminal

wiring terminal 

block

element

thermostat

active terminal

conduit adaptor 

goes in here and 

locking ring holds it

1/2"nipple

Summary of Contents for KCT27036A

































Reviews:

No comments