Kellfri 27-HTFL2E Manual Download Page 4

4

Table of contents

SAFETY INSTRUCTIONS

Before using the equipment or product, and for the safety of yourself and others, you must read the 

safety instructions and instruction manual and understand their contents. Always keep the safety 

instructions and operating manual handy for users of the equipment or product. For the safety of 

both yourself and others, it may be a good idea to read through the safety instructions every now 

and then. If the safety instructions or the operating manual are damaged, or become unusable 

for any other reason, new copies may be ordered from: Kellfri AB, Munkatorpsgatan 6, SE-532 40 

SKARA, Sweden. Tel: +46 511 242 50

The safety instructions can also be downloaded from Kellfri’s website: www.kellfri.co.uk
Do not use the equipment or product if you feel ill, tired or are under the influence of alcohol. Do not 
use the equipment or product if you are taking prescribed medication or drugs, or suffering from 
severe depression or mental illness.Always comply with general rules of the road and applicable 

rules stipulated by animal welfare legislation. People under the age of 15 are not allowed to use the 
equipment.

PRODUCT SAFETY INFORMATION

•  Keep the work area clear of other people; moving parts increase the risk of accidents.     Respect 

the equipment’s risk zone! Only the operator may be present in the vicinity of the machine while 

it is in operation. 

•  Children must never be present within the work area, never let children operate the machine.

•  The equipment works best and most safely when it is used in the capacity it is intended for. Do 

not attempt to alter the machine to increase its capacity.

•  Never leave the machine unsupervised when it is running. Switch off the engine and apply the 

parking brake when you leave the equipment – even for a short period. 

•  Never leave the machine in a raised position. There can be a loss of pressure in the hydraulics and 

the machine can drop to the ground.

•  Make sure that all guards are fitted and cannot come loose before use. The machine may only be 

used in the way described in this operating manual. Do not attempt to use or cut other materials 

such as metal and hard plastic.  

•  Operate a new machine at low speed for the first few hours, not at high speed and with a full 

load.

•  Avoid getting oil on your skin. If this happens, rinse thoroughly with water. 

•  Only the operator may be present in the vicinity of the machine while in operation.  

•  Do not use the machine without ensuring that all guards are correctly fitted.

•  To avoid accidents, inspect the work area and remove any harmful objects such as large stones 

and large branches, etc. before starting the work.  

•  Do not operate the machine if it is vibrating substantially; stop the machine immediately and 

check the machine.

•  Do not use the machine in inclement weather or in reduced visibility, e.g. in thick fog.

•  Exercise caution when working near power lines and telephone lines.

•  NEVER try to remove objects that have become trapped in the hedge trimmer while it is running.

Make sure that the equipment has stopped before taking action.

Children must not be left unsupervised in the area.

Warning! 

INSTRUCTIONS FOR EMERGENCY SITUATIONS

In case of emergency, call 112.

Always have a mobile phone or emergency phone available when working alone. A first-aid kit and 

fire extinguisher must be kept in an easily accessible location when carrying out any work, mainte-

nance or service.

Summary of Contents for 27-HTFL2E

























Reviews: